• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Search results

  1. C

    generic-control valve body problem?

    Block #4 is the lift block. You have already shown me that it has a problem as I have a constant pressure on the hose even with lever in neutral. This will be some serious labor. Thanks for any help.
  2. C

    generic-control valve body problem?

    Ford Backhoe 4 stick control valve body seems to have pressure on hose to lift cylinder even when controls are in neutral. Is this normal?
  3. C

    Need to get a little info if possible.

    Going to close this thread with results. Tractor still losing prime when shut down. Now each time it sits any at all. All gears work, but you can tell the pressure is weak. About as good as it ever was, so am going to finish project I was working on. Got to change out a busted hose and move...
  4. C

    Any comments on Quality Farm Supply?

    Looking to buy some hydraulic hoses from Quality Farm Supply and wondering about the hoses. Are they just cheap, low quality or a good grade of hose. Thanks for any comments.
  5. C

    Need to get a little info if possible.

    Partsandservice, I really appreciate your help with this project. Today, I got to do the vacuum test. Before I even got a reading, I was drawing oil at the entrance to the regulator. Reinstalled the assy and fired it off. Pump primed up quicker than it ever has since I've owned it. Didn't do it...
  6. C

    Need to get a little info if possible.

    Alright, I sure appreciate that. I will be in touch with them shortly. Going to pull a vacuum on the suction tube tomorrow. I have the pump all cleaned up and back together. Left the adapter assy snugged up but no pressure on the pump. Everything looks right now. If vacuum test is good, I will...
  7. C

    Need to get a little info if possible.

    There is a ring there and it was in place, but only contacting one barrel. I believe that if I can find a pair of barrels in decent shape, it may still work. That will be a last resort. Thanks for all the help. Much appreciated. There is a place in Simpsonville, SC with a fork lift graveyard.
  8. C

    Need to get a little info if possible.

    I found out why it protrudes. The cylinder with the bearings was cocked in the housing and would not go back inside. After I cleaned it some, everything fit. the springs in the adapter pushes them back out. I'll have to mount pump before mounting the adapter, using the factory gaskets. Now, just...
  9. C

    Need to get a little info if possible.

    and the rest.
  10. C

    Need to get a little info if possible.

    here are some more
  11. C

    Need to get a little info if possible.

    I believe you may be able to better see what I have with these.
  12. C

    Need to get a little info if possible.

    That is the way I have it installed now. But, before I put it in, I tried the gap with no seal or gasket. It was still open. The circles around the bearing and the shaft are raised above the regulator gasket surface about 2.25 mm, and the gasket is about .85 mm.
  13. C

    Need to get a little info if possible.

    That info about the seal helps by getting the seal fully seated. But still have a large gap with gasket on. It takes 2 1/2 thicknesses of seal to close the gap. I was filling the pump and ran out of oil. It pumps by hand, but that means nothing under pressure. Tomorrow, I will open pump for...
  14. C

    Need to get a little info if possible.

    Put it back together today with new gaskets that filled the gap. Put the pressure guage on and started the engine. Absolutely no pressure on guage. Removed guage and left plug out. Nothing, So. I will be looking for a pump. Thanks everyone.
  15. C

    Need to get a little info if possible.

    Yes, it was like that when I got it, but I didn't have any reason to notice it under the floor panel. I pulled it about 5 or 6 years ago to try to stop the losing prime. Ordered all new parts and they matched what came off. Ran it for a couple more years and parked it. Last year, I started it up...
  16. C

    Euclid green paint

    I don't know of any place now, but when I worked for NAPA, we sold Martin-senour paints. We could get custom cans for customers. Back then they were only about six bucks.
  17. C

    Need to get a little info if possible.

    pump sawzall blade won't fill gap to converter housing gasket in place the circles are raised and gasket goes on top of them. I see no way for it to seal.
  18. C

    Need to get a little info if possible.

    c gasket in place , pump side , converter side , gasket in place, I think I have found the problem. With gasket in place, there is a large gap between the parts.
  19. C

    Need to get a little info if possible.

    That sounds like a great idea! I already tried dropping the housing on a chunk of wood and it didn't work. But freezing it first could really work. I forgot to say in the description that the seat has a 1/4" hole right thru the middle of it. An ez out might work but I think it would ruin it.
  20. C

    Need to get a little info if possible.

    Unable to determine what seat is made of, but it appears to be metal. Round, about 1/2" wide, 1/4" thick, and countersunk to match the bottom of the safety valve, flat on the bottom. Button on safety valve seats in the countersink. The seat looks great, but I don't want to ruin it and not get it...
Top