• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Search results

  1. M

    Genie S-40 Boom lift joysticks stopped working.

    Ahh, Ok sorry that wasn't any help.
  2. M

    Genie S-40 Boom lift joysticks stopped working.

    Since it worked well the day before and doesn't work now, maybe its just the position it is parked in. Try to start the machine and move it with the ground controls to a new flatter position and see if the basket controls work now.
  3. M

    2011 Grove T80

    Ahh, ok so you know already what I know. Sorry I can’t be more help.
  4. M

    2011 Grove T80

    You can try this Manitowoc who is the distributor globally for Grove, here is their website: https://www.manitowoc.com/
  5. M

    Strange, interesting and funny stories buying and selling equipment

    it might sound weird but i've got to ask, did the question cross your mind that the buyer was the caller and not his "brother."
  6. M

    Genie 34/20

    Do you have a relief valve on your pump? I would make a small adjustment there and see if this works in your favor.
  7. M

    1979 Clark C300-50LPG Front axle question

    Did you match the new races with the old races? The new race looks a little tall to me, like it has 3/16" of stick out. In my experience the race usually sits flush or recessed.
  8. M

    Spool valve stuck, flush hyd lines or not?

    Recently I experienced the same situation on our Backhoe, I removed the spool and I ran a sandpaper flapper disk (like you would see on a drimall tool) up an down the valve body till I felt the nic in the valve body was gone. The same nic in the spool with be in the valvebody. I finished off...
  9. M

    Hyster UC-30

    I hope this helps, we have a lot of machines here and when we need to repack a cylinder we just take it apart and I'll take the old seals and guides to the hydraulic shop and have them match them up for new ones. Its quick and cheaper than the other route way in my opinion.
  10. M

    JCB 215S

    post a picture of the rear of your machine\
  11. M

    CAT hydro cylinder fail after a very short time......?

    Hey Fastline, I just want to say it sounds like the cylinder shop is doing right by it, I would go in with a humble attitude and allow them to fix their mistake, I'm sure they will.
  12. M

    6000m loss of brakes sometimes at idle

    it sounds like you have a leak and the nitrogen will keep leaking out right?
  13. M

    JLG telehandler no start issue

    It could be, and it could be anything, it’s hard for me to say right now. If I was working on the machine I would be 100% sure the ECM is bad before I purchase a new one, I would not just guess and put one on.
  14. M

    JLG telehandler no start issue

    Ok, I'm sorry this is about all I can figure to do with out being there to help you.
  15. M

    Connector for a Hyster Forklift tail light

    here is the female side: https://connectorexperts.com/i-31646596-ce6356m.html?ref=category:1261632 and the Male side: https://connectorexperts.com/i-31646595-ce6356f.html?ref=category:1261632
  16. M

    Connector for a Hyster Forklift tail light

    you can try this company: https://connectorexperts.com/
  17. M

    JLG telehandler no start issue

    Since you have a picture of all of your codes I would try to clear the codes and then attempt to start the vehicle, If it cranks and no starts on me I would then look to prime the fuel by cracking the nuts at the back of the fuel injectors one at a time while someone cranks the engine to see if...
  18. M

    JLG telehandler no start issue

    No I am sorry I do not have access to schematics
  19. M

    1999 JLG 450A 4 controls are not working from the basket

    Praise God! glad its working for you again!
  20. M

    JLG telehandler no start issue

    I would try and see if there is any water in any of your connectors first. I’m also curious if your machine wouldn’t start due to the power wash and now it’s been a few days if with the codes you got if you couldn’t just crack the lines at the injectors while you crank the machine to prime the...
Top