1. Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!
  2. ALL NEW MEMBERS READ THIS FIRST!! Thank you for joining Heavy Equipment Forums! If you are new to forums we communicate with "Threads", please search our threads to see if your topic may have already been answered and if not then click "Post New Thread" in the appropriate forum. This will allow all of our members to see your question and give you the best chance to be answered. After you've made a number of posts you will graduate to Full Member status where you'll see a few more privileges. Following these guidelines will help make this the best resource for heavy equipment on the net. Thanks for joining us and I hope you enjoy your stay!!

Recent Activity

Activity stream for all registered members at Heavy Equipment Forums.

  1. DB2 replied to the thread Wiper gland trouble Case 580C.

    Just have to give it some thought. As long as the gland and the base of the jack are square you should be ok.

    Jun 2, 2020 at 9:32 PM
  2. Polymath replied to the thread Wiper gland trouble Case 580C.

    I do have a hydraulic jack but not a press. I was considering ways I might utilize it in that manner but would have to figure out...

    Jun 2, 2020 at 9:29 PM
  3. Ammar_Jo posted a new thread.

    komatsu PC 80 mr-3 Overheating!!! HELP

    hello everyone, I'm Ammar from Jordan <middle east> I got a new machine delivered from germany so they have done something to the...

    Forum: Excavators

    Jun 2, 2020 at 9:29 PM
  4. DB2 liked DMiller's post in the thread Wiper gland trouble Case 580C.

    We used to use a Press and piece of Steel Stock to keep wiper seals flat to get it installed. You are installing what seems backwards?...

    Jun 2, 2020 at 9:24 PM
  5. DB2 replied to the thread Wiper gland trouble Case 580C.

    Hydraulic jack instead of a press?

    Jun 2, 2020 at 9:24 PM
  6. stendori replied to the thread john deere 310 sg shuttle shift isssues.

    just an update. checked all the wires which look good. strange is that if i pick up the front end with the bucket i can sometimes get it...

    Jun 2, 2020 at 8:54 PM
  7. DMiller liked Welder Dave's post in the thread Hough H80B source for parts.

    I think I'd talk to an equipment dealer before I went to Napa for advice on oil for heavy equipment transmissions. I think the Shell...

    Jun 2, 2020 at 8:50 PM
  8. DMiller liked Minnesota Eric's post in the thread Hough H80B source for parts.

    NLGI2 Grease, I guess I need to find something in a pail. Is Shell's 5W-40 T6 too thin for the engine? I have gallons of that on hand....

    Jun 2, 2020 at 8:50 PM
  9. DMiller liked kshansen's post in the thread Hough H80B source for parts.

    Well oil questions can cause a lot of opinions but my thoughts from what we used at the quarry would be as follows: Grease NLGI2? I'd...

    Jun 2, 2020 at 8:50 PM
  10. DMiller liked Minnesota Eric's post in the thread Hough H80B source for parts.

    Apparently I have a draw as the power was off. Both batteries were stones and I used an old dumb charger to get some juice in and two...

    Jun 2, 2020 at 8:50 PM
  11. DMiller liked kshansen's post in the thread Hough H80B source for parts.

    Well I would not want to make any definite statements about that machine, but.... if it is the wire that was connected to the ether...

    Jun 2, 2020 at 8:50 PM
  12. DMiller liked Minnesota Eric's post in the thread Hough H80B source for parts.

    I have every manual I can get my hands on. Two different operators manuals, a generic service manual for the DT466, a reprint of the...

    Jun 2, 2020 at 8:49 PM
  13. DMiller liked kshansen's post in the thread Hough H80B source for parts.

    Have you managed to get a service manual or maybe a parts book for this machine? Preferably both but either one would be a very good...

    Jun 2, 2020 at 8:49 PM
  14. DMiller liked Minnesota Eric's post in the thread Hough H80B source for parts.

    Thanks, kshansen! I want to take a pressure washer to this thing but it is also sitting on my clean concrete driveway surrounded by...

    Jun 2, 2020 at 8:49 PM
  15. DMiller liked kshansen's post in the thread Hough H80B source for parts.

    So if I'm seeing it right in these two pictures both those hoses are hooked to the same port? That is the port that should be connected...

    shutterstat.jpg Jun 2, 2020 at 8:49 PM
Loading...