• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Recent content by Txhayseed

  1. T

    2002 Cummins 4-390 engine???

    Didn't say how it dies. Just shuts off instantly ? Chugs to a stop with smoke ? Starts right back up with no issues ? Starts back up after cranking the starter till it catches ?? The diagnostics are always in the details the more you can provide the better.
  2. T

    Bobcat S300 works in high speed but only goes straight in low speed

    I would put a gauge on it and start checking pressures. Sounds like a flow issue or lack thereof. Sounds like your bypassing internally somewhere. A serial number would help. Putting a gauge on and seeing what your pressures are doing is a good place to start.
  3. T

    New to us Hamm H7i

    It's in the circuit board / fuse board under the step. Take out the four bolts. Swing it open and diag plug is built into the board. If it's not built into board and you said its a Kubota then you have to use the Kubota diag plug. It's built into the engine harness on the right side front if...
  4. T

    Kubota v1505 t rod bearing part number

    Maybe try kumar bros. I had a situation with hard to find parts on a tier 4 interum engine and they where able to get the parts. Only guys I could find that wanted to help and found me what I needed
  5. T

    10amp circuit breaker keeps popping

    It should be posted in service manual. I think they put it under the level sensor replacement section at the bottom. It will give you voltages and setting sequence. If you can't find it let me know.
  6. T

    Changing inside boom hoses on a 544 D 10 Gradall

    I always do them with out dismantling the boom. I just leave one side of the hose with out a fitting crimped on. Cut the old fitting off the original hose and cut a v notch about 1/2 back then put a tag line on it and a second line to attach the new hose to. Cut a v notch in new hose and tie it...
  7. T

    Doosan G90+wj dWJD-2a-T3 (C24) laid down on me...

    Rotating rectifier possibly ? We replace a few of those a year on the multi quip units. I would say wiring a more likely cause but just throwing out ideas
  8. T

    Bobcat 773 ECU programing ?

    Are we talking engine ecm or are you referring to the aux and or gateway controller ? Either way a bobcat dealership should be able to replace/update software with latest revision. Your dealer should have been able to tell you the issue by doing some simple checks right there not just that he...
  9. T

    10amp circuit breaker keeps popping

    Best way is to set it is using a volt meter. Gets you dialed right in with out issue.
  10. T

    Genie TMZ 34/19 electrical problem

    Qd 4 shows to be a 6 pin connector. The connector to your platform control box. Pin 2 on key switch should have 24 volts with e stop not depressed. Pins 1 and 3 will alternate 24v depending on if you have it in ground or platform mode.
  11. T

    Genie TMZ 34/19 electrical problem

    Key switch has power in from e stop on one wire. Second wire feeds ground controls third wire feeds basket controls depending on key position. Check for power in then switch positions for power to other two wires in both positions. If your not getting power into or out of key switch that would...
  12. T

    Doosan G90+wj dWJD-2a-T3 (C24) laid down on me...

    Do you have the key start model or the fancy pants unit with the digital display ?
  13. T

    Genie GS-2646 Scissor lift not powering up at all.

    So genie. Power goes from ground estop first. Through scissor stack cable then through platform estop to power up. Have you tried unplugging the control box from the Deutsch plug and then open the small side door on right side and plugging the control box in ? This will eleminate the scissor...
  14. T

    Doosan G90+wj dWJD-2a-T3 (C24) laid down on me...

    I know this sounds simple and crazy but is the selector switch door closed ?? And the door safety switch is working. I've actually had that scenario cause service calls more than once. Door not closed or bad safety switch will kill power generation.
  15. T

    Ingersoll Rand SD 70 Roller stops moving.

    Rollers are weird like that. And electrical grimlins are common. Shaking itself to death 8 hours a day week in week out can lead to some chaffing issues and failures for sure. Rollers always suck to. Filled up with dirt in every nook and cranny can't reach anything can't see anything since they...
Top