• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Recent content by turbotoys

  1. T

    2015 Leiberr l538 front end loader

    So while I was runninng the loader, I leaned over on a switch that was for the emergency steering. Notice 3 lights that showed up directly above the button for the emergency steering followed by a loud contiuous beep. Then the machine died and I have not been able to get it started again. It...
  2. T

    2015 Liebherr l538

    I purchased one of these last week. I have a few codes that I would like to further investigate. I found out the engine is a John Deer 4045HLC09. Does anyone know if the electronics are mostly deer also? I am lookine at buying heavy duty diagnostic software and want to make sure I get the...
  3. T

    fuel issue Takeuchi TL230

    Good morning, I did get that exact one you showed me on ebay. Thanks. Unit turns over great now. Still having no start issue. Quick recap, new filter, pusher pump (aftermarket) and I am getting a fuel supply out of fitting on side of injection pump. Leaning towards injection pump, is there...
  4. T

    fuel issue Takeuchi TL230

    The machine will not start. The machine would turn over 5 seconds at best and then I get a periodic on off noise from main relay
  5. T

    fuel issue Takeuchi TL230

    This is another view of fuel cut off solonoid..
  6. T

    fuel issue Takeuchi TL230

    Since I have solonoid out i decided to do a continuity test, top terminal to body of unit is 16 ohms.. Bottom is almost a short to body of unit.. 1/2 an ohm. seems like lower coil is not good. Shorted to body.
  7. T

    fuel issue Takeuchi TL230

    So I removed solenoid, turning key on then pushing rod in, it did not stay in. Starting, it still did not go in on its own. Machine would only crank for about 3 to 5 sec before the device in the photo started clicking. I added a pair of jump boxes and only got about 5 secs of cranking time...
  8. T

    fuel issue Takeuchi TL230

    Thanks EKimble and heymccall for information. I have a no start unit. last time it actually started I noticed a harder start, but it ran fine once it did. There was some rust around edge of fuel filter so I replaced, cleaned out water seperator installed a new pusher pump and now I have fuel up...
  9. T

    fuel issue Takeuchi TL230

    Would like to know if anyone has a diagram locating different components. I am trying to locate the stop solonoid timer and the stop solonoid relay. I am not getting but 4v to the pull wire on the fuel stop solonoid (assuming it should be 12V) and I thinking one of these components may be...
  10. T

    Takeuchi tl 230 skid steer fuel issues

    Based on those numbers I would guess stop timer has failed. Any chance it is the item with a one circled on it in 1st picture?
  11. T

    Takeuchi tl 230 skid steer fuel issues

    Lower picture is my fuel cut off solenoid showing wire colors. white wire ignition power. ( starts at 10.9 then when solenoid 1 shuts off goes to 12v) Green wire 3.6 v for about 1st 20 sec then bumps up tp 4.1 volts when component in 2nd picture de energizes.
  12. T

    Takeuchi tl 230 skid steer fuel issues

    That gives me something to look at today Thanks. Is it safe to assume that these two terminals need power all times for machine to run? I am not 100% it is the pull or the hold that I am getting 12v on. I do remember it is a green wire. Pull wire goes off from solonoid to stop relay and there...
  13. T

    Takeuchi tl 230 skid steer fuel issues

    Hello, my unit wont start. It gets fuel up to the fuel filter. I am at a point of trying to figure out how the actual fuel cut off solonoid functions. It has a two pole actuator. One is marked pull and the other is hold. For testing the solonoid manual says to apply 12v to pull then...
  14. T

    takeuchi 230 series 2 skid steer

    Hello So i noticed a lack of power and eventually machine would stall, now it seems like it willl start every once in a while but when I increase the load it stalls. I inspected fuel filter and it appeared to have a little water in it, I then drained the water seperator on back door. I also...
  15. T

    Case 621D no movement

    Helllo, auto shift now seems to be working, not sure if it was just a user error or something i did. I am now only concerned about the high idle. It seems to be around 1500 or so if I had to guess. I forgot to go to display box 001 to check the actual RPM. I tried disconnecting the actual...
See more
Top