• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Recent content by Seans problems

  1. Seans problems

    TB145 hydraulic pump/rexroth/uchida

    I was just asking if anyone had bought anything and if the places were reliable. I'll post after the order goes through and the pump is installed. Thanks again.
  2. Seans problems

    TB145 hydraulic pump/rexroth/uchida

    Our timing is pretty close.
  3. Seans problems

    TB145 hydraulic pump/rexroth/uchida

    Rexroth is huge but, our pumps are re-branded "uchida" pumps that they bought out and then shut the doors after the sale. I guess finding stuff for the 25 series and 18 series has been an issue for a lot of people. If these 145s have a spin on cartridge I might be blind, I've been all over this...
  4. Seans problems

    TB145 hydraulic pump/rexroth/uchida

    I checked the strainer, I was not aware there is a spin on cartridge. I'll go back in the manual to see where its at. Thank you. I have a good amount of bsp and jic stuff because of all the takeuchis we have.
  5. Seans problems

    TB145 hydraulic pump/rexroth/uchida

    Thank you, I saw this one and was wondering about quality. I will definitely call them and see where to go from there.
  6. Seans problems

    TB145 hydraulic pump/rexroth/uchida

    Thanks, I can time it by the manual and report back. I went off hooking up gauges to the pump itself and the pressure dropping intermittently from 3000Psi to around 2000Psi. I cant even find a manual for it.
  7. Seans problems

    TB145 hydraulic pump/rexroth/uchida

    Hi everyone, I have a TB145 S/N:14517385. The pump is very sluggish and sounds like its fighting itself on any movement, whether its tracking, swinging or digging. The strainer has been cleaned and the system has been flushed, I'm guessing I need a new pump. I cant find one anywhere beside...
  8. Seans problems

    Service Manual Trading Post

    Can anyone email me a service/repair manual for a gp-25 cat forklift? Serial number is: 5AM08659 If you have it for the engine and the chassis that would be huge, thanks.
  9. Seans problems

    Does anyone have a manual for CS56 roller?

    Thank you for the reply heymccall, Im set up for the online parts but that site is isn't as stream lined as it should be, or I'm just that great at internetting.
  10. Seans problems

    Does anyone have a manual for CS56 roller?

    Hi Everyone, Do any of you have a parts/service manual for a 2008 CS56 vibratory roller? Serial number is : CAT0CS56J-FCS00112 Thank you in advance.
  11. Seans problems

    Service Manual Trading Post

    Hi everyone. Does anyone have a service manual and parts manual for a bobcat 3400D? S/N is: AJNU12012 It stopped going into gear while its running. I lowered the idle and it helped but if I go back any further it'll kill the engine.
  12. Seans problems

    yanmar v4-5/v4-3 and mitsubishi ws310/410 parts suppliers

    Does anyone have a reliable dealer for parts for theses machines? They are over 20 years old and noone seems to have anything for them. I can find some engine parts through dealers but the rest seem like they are made of unobtanium.
  13. Seans problems

    Service Manual Trading Post

    Hi all, Does anyone have a service manual for a PC228 uslc-3eo? I have the maintenance and operation manual. Thanks
  14. Seans problems

    Has anyone here made their own sod cutter?

    That's a pretty simple design, thanks a lot for pointing me towards it. I think I'm gonna try to fab it out. I think just a fairly narrow bucket blade should do me for the cut.
  15. Seans problems

    Has anyone here made their own sod cutter?

    We have an 18" ryan sod cutter from 1988 thats a push behind but sometimes I think about modding one of our skidsteer buckets and adding a blade and roller to take out more faster. It'd save so much time and money. Has anyone done anything like this?
See more
Top