-
Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!
Recent content by pro94lt1
-
P
what oil for cl 455 manual transmission?
Thanks I drained and filled with 80 90w gl5 gear oil. -
P
what oil for cl 455 manual transmission?
I'm wanting to change the oil in my transmission it's a Clark 455 From what the manual says it's Gl5 80w90. So just Gl5 gear oil? This is a synchronized tranny so I was wondering if it needed something added for that? -
P
toro dingo 220 hydraulics sticking
Got a little 220 dingo and the hydraulic controls are sticking... anything I should do or look for?- pro94lt1
- Thread
- Replies: 0
- Forum: Mini Skid Steers
-
P
Park brake not holding
Air chamber with 2 air lines going in the chamber is held by 2 studs the threaded rod is going to a lever that operates the drums. It is conected to 2 pins. Their is a 14mm bolt in the slack aduster? And a 10mm on the top? Trying to load pics. The brakes stop like a dream. Drums have 3/4 an inch... -
P
Park brake not holding
Thanks guys... I understand the importance, I'm trying to figure it out. It won't roll on a hill but in gear it will move if that's a better description I just don't want it to be able to move. I've got pics but can't upload them... -
P
Park brake not holding
I'm not sure what brakes it has other than air, and it's an auto so I have to have a functioning parking brake... -
P
Park brake not holding
Got a 2002 c7500 with air brakes, the parking brakes are not holding... are they just to loose? Thanks for any recommendations -
P
3126 huei oil line...
Just got a 2001 3126 in a c7500 the black rubber oil line going to the huei pump is leaking. My questions are is there anything I need to know about changing it and is it a cat only part??? -
P
8.2 Detroit no start...
That's good to know. How much was it? Also this is the electronic governor not the mechanical one that was in them from 81- maybe 86... If it were the older one I'd have it fixed. .. -
P
8.2 Detroit no start...
It will always start if I have a helper start it while I manually slide the rod over that comes out of governor. It's a shame I've got 2 manual governors but this one is electronic and different anyone know where to get one? -
P
8.2 Detroit no start...
I think I've narrowed it down to the governor, and the solenoid inside it. It's got juice but no clicking. I manually held it open and it started ran fine for 2 hours shut it off and today no go. This governor doesn't have the solenoid that you can see on the outside. .. -
P
8.2 Detroit no start...
My 89 get 7000 is my money maker, parked it Wednesday running great went to start it today and nothing. I gave it a shot of ether and it hit I'm stumped. Filters are a month old. I'm not sure where to even start not sure it has a lift pump? HELP! -
P
wheel shakes after bumps?????
This truck doesn't have a stabilizer on it... The front end is extremely tight no slack except for where the power steering cylinder that helps turn is mounted to the frame... I had just put brakes and a caliper on the front and hoping I just had the wheels on cocked. If it does it again guess... -
P
wheel shakes after bumps?????
Got a 89 gmc 7000 out of the blue it has started shaking like crazy after you've hit some bumps in the road... could my dayton wheel have been on crooked enough to cause the shaking? -
P
81 gmc 7000 brake job
Got a 81 gmc 7000 that one of the wheel cylinders is leaking on front and I'm fixing to fix is it a straight forward job? Any specific tools I need before I tear into it? I'm guessing I'm going to break all the steel lines when I remove them...