• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Recent content by pasinead1991

  1. pasinead1991

    KOBELCO SK 210 -6E

    Thank you for the download very helpful I will check over the weekend and will let you know what I found.
  2. pasinead1991

    KOBELCO SK 210 -6E

    No hoses burst and no valves on cylinder it has some sort of a way to stop oil flow before the cylinder rod comes to a stop I believe it’s a valve on the valve chest that dose this would anyone have a detailed break down of the valve chest/body. The arm works fine until you reach the end of its...
  3. pasinead1991

    KOBELCO SK 210 -6E

    Hi everyone I have a problem with a kobelco sk210-6 when arm is all the way out it falls back in but only if all the way out otherwise function is normal
  4. pasinead1991

    ZX290-5N no throttle response

    Hi everyone I have a ZX290-5N with no throttle response I replaced control panel with control dial in all one unit and still no throttle response checked all wiring all seems good check voltage at dial only have 2.4 volts where I should have 5 volts. it dose not use a cable and stepper motor. Is...
  5. pasinead1991

    Cat 325C

    Ok thanks again.
  6. pasinead1991

    Cat 325C

    I’m going to ireland for 10 days will finish it when I get back the owner wants to get a used ecu I’m not sure if that will work aren’t the ecu s programmed to each other. Thank you for your help again.
  7. pasinead1991

    Cat 325C

    Will do thanks so much
  8. pasinead1991

    Cat 325C

    Thanks very much my email is pasinead1991@yahoo .com. The ecu underneath the main won has me worried also it’s for the hammer you said. The lights don’t light up on that at all I guess if the hammer won’t work that’s my problem I opened it and it was very wet and corroded I cleaned as best I...
  9. pasinead1991

    Cat 325C

    When I put it on manual the swing works and I can increase engine speed with the other switch next to it increase it or decrease it no problem.
  10. pasinead1991

    Cat 325C

    Yes it has a hammer and I meant swing thank you for that info. The yellow light is on on the upper ecu which means no Communication to the monitor I checked all the wiring from the monitor right to the EC you all good good continuity and all the wires I’m getting a new monitor I will let you...
  11. pasinead1991

    Cat 325C

    Thanks I will check that wiring should the lower ecu lights lite up when it’s powered up with key on.
  12. pasinead1991

    Cat 325C

  13. pasinead1991

    Cat 325C

    Hi everyone I’m working on a cat 325 c that has no hi idle and won’t slew checked all pressure switches. Monitor gauges come on with key on and then won’t read anything it starts monitor says ECM error. There are 2 ecu s behind the cab one has lights come on red yellow and green then red hose...
  14. pasinead1991

    973 C track machine

    Hi everyone I posted before that track machine wouldn’t rotate it’s self after installing new head on left drive motor problem was there were no shuttle valves in the new head swapped them out from old one and resssemble and now works good thanks for the help.
  15. pasinead1991

    Track loader

    Hi every one had a problem with 973C loosing pressure when turning 360 left or right turned out to be a crack in the head of the left drive motor repaired and now no more trouble codes machine works good but when turning sharp left or right the left track didn’t seem to be getting the same power...
Top