• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Recent content by olfolks

  1. O

    Cat 120G Serial Number lookup, Blade questions

    Side shift made turning the blade around easier , but moving snow I seldom used it. The float option was the best for snow on blacktop
  2. O

    IH 500E won't move.

    before u get in too deep if it is like the 500c check the hose that supplies fluid to the convertor it is on the left side of the tranny; mine quit moving like that and the hose had a hole in it allowing the charge pump to suck air
  3. O

    D6c cat loss of oil pressure

    I am starting to understand how MOM felt when AS the world turns went off the air
  4. O

    About how much does a D4D weigh with...

    the cat performance hand book edition 13 says 13000 pounds bare tractor no blade no rops no winch
  5. O

    Hunting parts for my 15A Cat

    off road equipment shows they have 4M9112 used for 96.00 bucks it also shows 4M9111 as a piston and linner group for 200-360 bucks some cat some aftermarket the 3S4040 and 5M9053 all come up as the above numbers sorry the 5M9053 was a piston ring shows none in stock
  6. O

    Fiat Allis FD5 wont steer

    kicker, which manual are u wanting the parts or the service I can see what I can do about making a copy it maybe cost or time prohibitive lol
  7. O

    Fiat Allis FD5 wont steer

    I looked at the manuals last night and they have no clue as to where they came from they are reprints for sure the are loose leaf pages in a binder crane and tractor in ohio is a source of parts as well as any case dealer or new Holland ag dealer if u have the part numbers the service book...
  8. O

    Fiat Allis FD5 wont steer

    I will try to remember to look at the ones I have and see if it says where they came from. sometimes I get sidetracked when I get home from work LOL I am sure these are reprints but they came with the dozer so not sure how old or where they came from give me a few days
  9. O

    Caterpillar D7 17A fuel filter

    also on the slobering check your compression release settings after I redid the heads on my 3t it did the same thing , I found that I had 2 of the comp release rods too tight also after 3 or 4 hours hard running u should retoqre the heads and check valve clearance
  10. O

    Hydraulic vs pto winch

    not sure what you are trying to do with what size winch but I have a 10k military winch and was going to put a hyd drive on it and use it off the back of a tractor for pulling logs up out of the woods reason I wanted to go hyd was 1 it lets u reverse the winch while under load and 2 should...
  11. O

    Fiat Allis FD5 wont steer

    When u say idler which one u mean front, top , bottom ? Lol new holland dealers and case dealers both can get parts for these if they are a viable If the clutches were bad it wouldn't pull on that side I would think A worn brake band is more what I am thinking I have ran dozers with...
  12. O

    Fiat Allis FD5 wont steer

    the plate is on the floorboard not the dash itself on mine it is a black colored plate about 4 or 5 inch sq lifts up from the frt
  13. O

    Fiat Allis FD5 wont steer

    rb we run hyd fluid in the trans and the steering clutches as they are in the same rear compartment u fill/check under the seat. the tourqe convertor takes atf and is checked/filled under a small plate on the right outside of the dash we use hastings filters on ours I can get the numbers if...
  14. O

    Fiat Allis FD5 wont steer

    The cap/plug behind check port "P" is what I took apart there is a spring in there but it won't fly out The cap 4 is the check valve cover I would say the check in urs is stuck only letting the left side work But I would start with the top valve as it is easier to get to if I remember...
  15. O

    Fiat Allis FD5 wont steer

    sorry but they didn't come out in order lol page 1 is 3rd from the last followed by 6 and 7 which are the spec's I would take the plug and valve off the top as this can be done without removing the whole block from the tranny
See more
Top