• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Recent content by norman123

  1. N

    volvo bl60 hood release

    cool. cool. find it. thanks.
  2. N

    volvo bl60 hood release

    HI, just bought a volvo bl60, anybody know where is hood latch release?
  3. N

    Belarus 250

    Bought a belarus 250 tractor month ago from auction. Steering was good but steering not turn at all after parking, any idea?
  4. N

    Cat 262 2 speed button

    thanks Chrisso and Nige. Gave it a try yesterday, put a toggle switch between pin 7 and pin8. Started engine and machine was not moving, then figured hydraulic oil is low. Turned off engine and didn’t touch toggle switch. This morning put more hydraulic oil. And engine didn’t crank at all. Now I...
  5. N

    Cat 262 2 speed button

    Bought some dt connector from amazon. As diagram shows pin 7 and pin 8 r for 2 speed. Will it work if I put a toggle switch for pin 7 and pin 8?
  6. N

    Cat 262 2 speed button

    Recently replaced right hand joystick. Trying to do something at lefthand joystick.question is there is only one button on it. And wire broken connected nowhere. Wonder if I can get 2 speed working since it is so slow now. Found a wire diagram. Anybody have a experience to get 2 speed work?thanks
  7. N

    01 cat 246 joystick repair

    follow up this just in case some one else have to repair joystick leak. My machine is cat 262. Recently ordered plunger seal from cat. Took the whole thing out. And got all hydraulic oil leak under machine. When everything is done. I realized I don’t really need took whole thing out of just...
  8. N

    Question about cat 3204di engine camshaft gear

    As I know this engine dont have liner. gasket Looks like a liner. Try to save as much as I can. Is that possible do block work and change just pistons and rings?
  9. N

    Question about cat 3204di engine camshaft gear

    Cool thanks.done. One one question. Since there is no sleeve in block. Still need machine work at block if I decide to press sleeve in?
  10. N

    Question about cat 3204di engine camshaft gear

    Rebuild a smoke cat 3204 engine. Brought engine to shop,but they just want the block to bore ocersize. Tried to remove camshaft gear, on manual it says remove bolt (9) but i dont see any bolt. Anyone can help?already remove the bolt and plate that holding camshaft behimd the Camshaft gear.
  11. N

    cat 262 skid steer project Coolant drainage plug

    Yes. I got floor panel pulled and changed throttle cable. Got all dirty stuff out under seat and floor. I am double the former owner ever cleaned this a 15+ years old machine.
  12. N

    cat 262 skid steer project Coolant drainage plug

    Yes. Keep it clean. That's what I did a few days ago. Got a pile of dirt /grease/trash Out of it.
  13. N

    cat 262 skid steer project Coolant drainage plug

    heard about grapple bucket welded to quick connect? Any idea to cut it back to normal quick connect?
  14. N

    cat 262 skid steer project Coolant drainage plug

    Thanks for the information. put it back original is already at my list:)
  15. N

    cat 262 skid steer project Coolant drainage plug

    I used a pvc 90 to connect the air filter housing, and all other parts to the engine intake ordered from cat. Air filter number is 300043023. when I got the machine,The air filter housing was in cab.
Top