• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Recent content by muski

  1. M

    cummins smoking!!

    hi pump guy well you were 100% correct!!!! the shop came back took our chipper then told me the pump was rebuilt wrong ??? think they are liying but either or we got it back and now its running fine no smoke at all!!!! i think like you said the pump was installed incorrectly. thank you for your...
  2. M

    cummins smoking!!

    thx for your help pump guy. pump only has 700 hrs on it so it must have to do with the timing. wouldnt think the body of pump could be worn too bad yet. the shop that installed it said its kind of like an automatic thing as far as setting lever over before installing.told me you dont need to do...
  3. M

    cummins smoking!!

    hey pumpguy thx for reply. a little update i did the test a second time and with block in it lightly smoked but not enough to drop rpms.then took block out tried again and did same thing lightly smoked and didnt drop rpm. gonna try again today without block but do you think this is still the...
  4. M

    cummins smoking!!

    ahh yes knew it was a stupid question lol
  5. M

    cummins smoking!!

    ok i did the test and instead of 5 sec till it started smoking it took maybe 30-40 sec till it started smoking.does lever need to be fully forward or just open say 1/2 inch??then took block out and tried again and still took 30-40 sec before smoking so bad that rpms drop right down.then go back...
  6. M

    cummins smoking!!

    holy crap i did it!!!! lol not too comp. or phone savvy but there it is. so you are saying put a block between the plunger peice that has coolant lines going to it and obvi. the lever in front of it??also this is a stupid question but what is the csd that needs to be disengaged???
  7. M

    cummins smoking!!

  8. M

    cummins smoking!!

    yes it does have coolant lines gonna try and get a pic in here
  9. M

    cummins smoking!!

    what i was thinking at first but the coolant level has never gone down
  10. M

    cummins smoking!!

    gonna go pull side cover and take a look but i dont think it has cooling lines running to it. after it gets to operating temp and go to full throttle then 5 sec later smoking,but only at full throttle if you idle down smoke stops and runs fine.
  11. M

    cummins smoking!!

    hello ,yes they said they drained tank and flushed it out and put fresh fuel in it.havent tried alt fuel source yet. thx for reply oh and yes has a fuel /water separator which is new and the 1st thing i did was drain into a clean pan and didnt see 1 drop of water.100% fuel
  12. M

    cummins smoking!!

    hi wes just checked work order from shop.they said pump that was on it had rust inside and sent it out to be rebuilt. so they didnt replace pump just had it rebuilt. maybe rebuild job went bad because it ran great no smoke for 1st 2 hrs and now it only takes 5 sec of full throttle and starts...
  13. M

    cummins smoking!!

    thx wes. not sure what kind of pump they replaced it with but will try and find out!!!!
  14. M

    cummins smoking!!

    hello everyone!! i know its been a while and thats because we took chipper to a diesel engine shop not a cummins dealer.well they went through it,tested injectors they are fine.they were brand new but they checked them anyway. came to conclusion it was the fuel pump. now this would be the 2nd...
  15. M

    cummins smoking!!

    you are prob right with the -z- symbol embossed on the side. weird thing is this engine has been to dealer would say 2 yrs ago and had the pump replaced but whose to say it went bad already.this could be my whole problem. thanks birken!!!
See more
Top