• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Recent content by mattyt1984

  1. M

    Deutz f4l 1011

    I'm getting closer to getting this figured out I synced each pump while engine was in full rev and got it to little smoke. Still seems like it smokesa bit much. Anyway to determine shim height or possible to run with no shim? I think my head gasket may be different thickness than original...
  2. M

    Deutz f4l 1011

    When I swapped the pumps it didn't seem to make much difference. By turning the pumps that just adjust fuel amount current?
  3. M

    Deutz f4l 1011

    I did swap them all cylinders seem to fire but some better than others. I did compression check again all were 400 psi or more. The engine seems to run ok just the smoke I am concerned with now. I also replaced all injectors with new
  4. M

    Deutz f4l 1011

    How do you adjust fuel timing? I checked cam to crank and it's right on. Can the fuel pumps be shimmed with thinner gasket or none? It seems like they need to fire a little quicker so engine won't smoke. Any suggestions?
  5. M

    Deutz f4l 1011

    How do you adjust fuel timing? I checked cam to crank and it's right on. Can the fuel pumps be shimmed with thinner gasket or none? It seems like they need to fire a little quicker so engine won't smoke. Any suggestions?
  6. M

    Deutz f4l 1011

    I replaced Cam. Timed engine. It's starts and runs but cylinder one and 2 cause engine to smoke. If I disconnect the injector lines on those two cylinder smoke mostly clears and it sounds about the same. I did a compression test and both tested above 400 psi cold. I put in new injectors and...
  7. M

    Deutz f4l 1011

    How does camshaft come out? I removed retaining bolt from rear. Does it pull out the front?
  8. M

    Deutz f4l 1011

    Yes I have the pins.
  9. M

    Deutz f4l 1011

    What's the cheapest belt tensioner to use for these?
  10. M

    Deutz f4l 1011

    Yeah I got the new timing belt and tensioning pulley only thing I don't have is tensioner. What is the cheapest option for that?
  11. M

    Deutz f4l 1011

    I removed unit injector pumps and I could see valve lifter is broken. Looks like I'll be removing engine from stump grinder and ripping it down. Looks like a time consuming task.
  12. M

    Deutz f4l 1011

    I have a deutz f4l 1011 issue is push rod adjustment on rocker needs be threaded out so much the lock nut won't go on. All the others seem to lift and adjust well. This seems to be missing like 3/8 inch of lift when closed. Any common issues with these I'm thinking it could only be cam or...
  13. M

    Bombardier sw48 hy sidewalk plow manual

    I still couldn't find manual. Issue I'm having is it needs to run for a minute or two then it moves and works as it should. Just trying to figure out why this is. If I shut off and be restart it works fine as long as it's warm. Also I don't know what all the switches are for
  14. M

    Deutz 912/913 oversized bearings

    I have a crank to have ground what is largest I can get I'm only seeing .030 in but I need .040 in to cleanup the crank I have.
  15. M

    Cat 950H loader loading a non runner

    Looks pretty easy to releae brake. What is easiest way to get bucket up in the air? Will I just need battery power lift with key on and lift bucket and lever pull back on bucket lift stick at same time?
Top