• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Recent content by Jrod25

  1. J

    Cat 9 pin diag port pin layout

    Ok thanks, I think I'm going to buy one of these, so for my 2013 272D XHP, it doesn't matter if it's an adapter II? I thought I needed adapter 3 but I really do not know what I need apparently. I only need it for my 272d, I would not be using on other equipment
  2. J

    Cat 9 pin diag port pin layout

    Yes, the problem I have is it I can't really tell which is the fake and which is the real deal
  3. J

    Cat 9 pin diag port pin layout

    Aftermarket. I only purchased for this one skidsteer, so not I never have connected to anything else. I was reading online, I'm not sure if it's true or not, but that cat has different 9pin to 15 d-sub pins for different applications, so idk.. I ordered another cable from one that states it's...
  4. J

    Cat 9 pin diag port pin layout

    Does anyone have the pin diagram for a 9 pin cdl/cat ( for a 2013 skidsteer) to that goes to the 15 pin D-sub connector? I'm starting to wonder if I'm using the wrong adapter and that is causing my issue where the J1939 isn't showing its communicating properly (incomplete). Attached it how mine...
  5. J

    CAT 299D Fuel leakage code...

    This summary data is from a 20-30 minute run. DPF differential pressure: about 0.13–0.50 psi. SIS DPF differential pressure regen trigger range: 0.9–1.5 psi. DPF soot loading: about 39–42%. DPF soot mass: 8 g. DPF soot mass #1: 4 g. DPF soot mass #2: 9 g. DPF regen level: Regeneration Not...
  6. J

    CAT 299D Fuel leakage code...

    Yes I saw that, I was just trying to confirm it's ok in my case. There is conflicting messages between the sis troubleshooting doc and Et, in the sis doc it sounds like it's ok to reset it, but in et when you click on reset it states "do not reset unless the dpf has been cleaned"
  7. J

    CAT 299D Fuel leakage code...

    I would say active. I was trying to see if it was safe to move to logged (reset) to see if it came back or not. Based on what I could see in ET, it hasn't tried to do a regen in a long time, since before this, get your head issues from what I could tell according to what the old owner told me...
  8. J

    CAT 299D Fuel leakage code...

    i hope I didn't post in the wrong place, didn't me to high jack and thread
  9. J

    CAT 299D Fuel leakage code...

    Nige, I have the same code, ET says it's only happened twice, and many hours ago. I ended up replacing the fuel rail limiter, and all four of the injectors were leaking really bad on the overflow line. I didn't really smell fuel in the oil. But with my basic ET testing to me it seems like it's...
  10. J

    Error with ET 2024A and 478-0235 Comm Adapter 3

    Did you ever find a solution to this, I have a 272d and it's always show "incomplete" on my Machine Control on my ET. But all of the switches all seems to be recognized correctly, so I close the door, lower the arm rest , etc . Everything shows in ET is communicating like it should.other than...
  11. J

    CAT 299D Fuel leakage code...

    I. Et you do an event logging or live data display when cranking, you'll see a desired fuel pressure and then the actual fuel pressure. That's how you know if you're meeting what's expected.
  12. J

    CAT 272D XHP No Lights or power to monitor, no crank

    Update, so all the injectors were leaking, was another part of my problem, now that they are replaced along with the hp overflow limiter replacement on the fuel rail it starts right up every time. Thanks again for everyone ones help, now I have to deal with a couple more lingering issues I have...
  13. J

    2013 272D XHP Help understand high fuel pressure operation

    So this was unexpected...when I removed all four injectors that all just slipped right out, I was expecting some resistance from the seals when removing, but they all literally just lifted right up with no pressure.. I wonder what caused this and why
  14. J

    2013 272D XHP Help understand high fuel pressure operation

    Well by least expensive and the angle I was was coming from was I meant buying from Kubota and paying Kubota prices instead of paying CAT prices for a Kubota engine.
  15. J

    2013 272D XHP Help understand high fuel pressure operation

    On the topic of Injectors, my CAT has a Kubota engine: Engine C3.8 Arrangement 345-3555 Serial 2GL0419 And the least expensive set I have found is $800 for a set of four, but I came across these and to me they look like they are exactly the same as the ones recommended but only $400...
See more
Top