• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Recent content by Joeyinstx

  1. J

    Johne Deere 650J Fuel Rail Pressure

    Here is the video of the fuel rail pressure releif valve test. Lookss like the valve is bad because its allowing by pass of fuel at id Just uploaded the vodeo mg2361
  2. J

    Johne Deere 650J Fuel Rail Pressure

    Here is the video of the fuel rail pressure releif valve test. Lookss like the valve is bad because its allowing by pass of fuel at idle.
  3. J

    Johne Deere 650J Fuel Rail Pressure

    Thank you everyone for the input and advise. Machine is running fine so I'm going to schedule a software update as mg2361 suggested.
  4. J

    Johne Deere 650J Fuel Rail Pressure

    Pressure cold was 7.5k
  5. J

    Johne Deere 650J Fuel Rail Pressure

    Fuel rail pressure fluctuating between 7k and 10k?
  6. J

    Johne Deere 650J Fuel Rail Pressure

    Hello there, The SN is T0650JX160150. HPCR pump was replaced because of rough running at idle and only developing 2250 at full throttle no load. The pump replacement fixed the above problems. No rough idle and max rpm is 2350 no load with new pump. As per my original message only showing...
  7. J

    Johne Deere 650J Fuel Rail Pressure

    I just replaced the high pressure fuel pump on a 650J. I was wondering what the normal operating fuel rail pressure is supposed to be? I’m getting a reading of 7540 psi at full throttle. Thanks Joe
    • Joeyinstx
    • Thread
    • 650j fuel pimp fuel rail john deere 650j
    • Replies: 12
    • Forum: Dozers
  8. J

    John Deere 310SG wont move

    Had a similar transmission problem with a 310J power shift. Turned out to be a faulty K2 - Ignition relay, was not energizing part of the fuse buss, specifically the F36 transmission control fuse. Replaced the K2 relay and everything worked perfectly.
  9. J

    John Deere 310J Backhoe Won't Start

    MG, Thank you. I got cap and contacts kit for the fuel solenoid. I will install it even though the code disappeared when cleared. I will post my progress.
  10. J

    John Deere 310J Backhoe Won't Start

    MG, I replaced the Vehicle System Monitor because the screen was hard to read from sun exposure. I’m getting these errors: After bulb test: low fuel level - I know it’s a bad sending unit. Also getting converter temp fault. Active Codes: SDM 177.03 and SDM 224.02 They reappear even after...
  11. J

    John Deere 310J Backhoe Won't Start

    MG, I’m traveling and won’t be close to the machine for a few days. When I return I’ll run the tests you mentioned. Thanks
  12. J

    John Deere 310J Backhoe Won't Start

    No stored codes.
  13. J

    John Deere 310J Backhoe Won't Start

    MG, The vehicle monitor shows 220 rpm during crank.
  14. J

    John Deere 310J Backhoe Won't Start

    Morning MG, No active codes in system. Any other ideas. Fuel tank level sending unit is not working, showing empty tank even though tank is full. Will this shut injection pump down?
  15. J

    John Deere 310J Backhoe Won't Start

    MG, will try in the morning and let you know what I find. Thanks.
See more
Top