• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Recent content by Greenmonzter

  1. G

    2010 Genie S-65 calibration issues

    S-65 boom lift fault code said joystick was out of calibration... calibrated the joystick then it said boom angle sensor needed calibrated, I calibrated the sensor, then it said boom angle sensor had a low value. We have 2 of these machines and they both are currently down due to problems with...
  2. G

    Loud cladder coming from motor or transmission

    Well I checked the flywheel and adaptor plate no issues with those.. when I start machine with the drive shaft out no noise... ive determined the noise is coming from the input shaft and converter housing on the transmission.
  3. G

    Loud cladder coming from motor or transmission

    I gotta genie 1056 with a jd4045 and a dana spicer t20000 its had some problems and now it's super loud claddering sound it's making I can't figure out.. first off not long after purchased the machine transmission when out so sent it to pj to get fixed was fine for a year then breaks drive...
  4. G

    Genie 1056

    Gotta 1056 that has been stalling during operation a few weeks now I havent been to track down the cause..then today it twisted the yoke out of the rubber isolater inside the shaft.. Transmission issue? Or converter clutch locking up intermittent??
  5. G

    Gth-844 with perkins engine

    Machine is not cranking over. Just had it serviced and i think its been over filled with oil... Based on the dip stick its above the full mark... It was running fine then it died.. And wont crank over..
  6. G

    Gth-844 genie leveling issue

    Id say that the rear axle is oscillating. Check out the attached pic.. I figured it was okay just an a**hole forman, that isn't a operator..
  7. G

    Gth-844 genie leveling issue

    Well ive always keep my hand on the sway button when driveing over uneven ground.. And never have had a problem with it .. But On one of our site's we gotta a real picky forman.. Our machines aint new they all got 5 to 6k hours on it. I was trying to recreate the complaint and i did.. I slide...
  8. G

    Gth-844 genie leveling issue

    Does a 2012 genie 844 have a self leveling feature?? I dont mean chassis sway when working on a hill .. I mean like driving over uneven ground.
  9. G

    GENIE GTH-1056 transmission

    I cant seem to find what oil to put in this machine. oil in it is clear and clean... it just alittle low...
  10. G

    genie 1056 stalls

    its got 6155hrs... It is 2012 and it has a digital display on the dash that will display fault codes when ecm detects irregular engine conditions. I serviced the machine today and cleaned the radiator, they used it all day without it stalling. I took temp readings threw out the day also with...
  11. G

    genie 1056 stalls

    I do have infrared temp gun.. what would the degree tolerance be?? between 180°~220°. I'm kinda new to the heavy equipment world. been wrenching my whole life, just not on a diesel engine. So i am open to all the information i can get
  12. G

    genie 1056 stalls

    I gotta gth-1056 10k forklift has a john deere 4045 engine..gets hot and shuts off. radiator is full, no coolant leaks.. no fluid on ground
  13. G

    cat th 63 excessive smoke

    How can i determine if turbo has failed or failing
  14. G

    caterpillar th63 fork lift

    I have a caterpillar th63 it has excessive smoke comeing out of blow by tube... Hard to start in the mornings... I was told it maybe possible turbo issue...how can i check turbo to see if it is bad...m
See more
Top