• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Recent content by gm@diezel

  1. G

    Bolt torques on a Deutz TCD2.9L4

    Does anyone have bolt torque specs for a Deutz TCD2.9L4 engine used in a Cat 5500 lb telehandler? I'm having trouble finding a workshop manual anywhere that has the specs in it and was wondering if anyone can help me out?
  2. G

    Case 1840 Loader Drop Issue

    Unfortunately it's not a linkage issue. Linkage is good and tight and greased up and moves freely.
  3. G

    Case 1840 Loader Drop Issue

    So I'm working on a Case 1840 skid steer that has a loader problem. Haven't worked on these much so this one I need a little help on. It is a late model 1840 with a late serial number. Has the issue with the loader dropping when you move the lever slightly in the raise position. Has lots of...
  4. G

    Takeuchi TL8 No Hydraulic Funtions

    I have a Takeuchi TL8 that has no hydraulic functions and I am quite sure it is a electrical issue. I need a wiring schematic to figure out where the relays and fused are. Can someone help me with that? Thanks
  5. G

    CAT 257B Track Skid Loader Interlock Issues!

    So I finally have figured out all my problems. The no start issue was the bad lap bar sensor. The interlock issue was the work tool detent coil which is located under the boot of the right hand joystick. Apparently it was shorted out. Unplugged that and all my problems went away! Got a new one...
  6. G

    CAT 257B Track Skid Loader Interlock Issues!

    Got my new armrest switch and installed it. Machine now starts as it should so that took care of that problem. But unfortunately I still have both park brake and seat belt lights flashing. So I'm going to check all solenoids and wiring going to them and see what I come up with. Any more...
  7. G

    CAT 257B Track Skid Loader Interlock Issues!

    Hey we're on to something now! Jumpered G985 and 202 and now it starts! But I still have both flashing lights. If I have a bad seat bar switch could that be making the lights flash?
  8. G

    CAT 257B Track Skid Loader Interlock Issues!

    So when I check continuity at the plug at the ECM I don't get any continuity at any of the two wires with the armrest up or down. So I jumped G984 and 202 and got continuity down at the ECM but the machine still will not crank. Am I doing it wrong?
  9. G

    CAT 257B Track Skid Loader Interlock Issues!

    So I cannot get any continuity on the seat bar switch. I would like to jumper the wires and see if it works. There are three wires going to the switch and I am wondering which ones do I jumper together?
  10. G

    CAT 257B Track Skid Loader Interlock Issues!

    What is a good way to check the seat bar switch? I also have not checked the door switch. Serial #SLK06521.
  11. G

    CAT 257B Track Skid Loader Interlock Issues!

    Hello, I have a CAT 257B Track Skid Steer that seems to be having interlock issues. Here is what the machine is doing. Both seat belt and park brake lights are flashing constantly and the machine with not attempt to crank or operate. I have read some about the solenoids but havent been able to...
  12. G

    Kubota SVL95-2 Codes E026, E027. No start.

    No need to worry your heads about this issue. I got a clue from a Kubota guy. The new wiring harness has all new fuses installed but not relays which I never realized and never took the cover off to check. Put relays in and of course the issue went away!
  13. G

    Kubota SVL95-2 Codes E026, E027. No start.

    Hi. I have a 2016 Kubota SVL95-2 that is throwing E026 and E027 codes which I understand is no communication with the ECU and ACU controllers. It has a new wiring harness in it due to a small fire starting in the engine bay. There is no voltage on the CAN high and low circuits which I believe to...
  14. G

    Volvo A35 Haul Truck Drop Box Speed Sensors

    The machine serial # A35V2400. It is a 1994 model. I replaced the SE55 sensor and also a cracked air line at the solenoid and now the machine seems to shift from high to low okay and drives. My tachometer on the dash doesn't work though and could that lead to a faulty engine speed sensor?
  15. G

    Volvo A35 Haul Truck Drop Box Speed Sensors

    Recently purchased a 1994 Volvo A35 haul truck and having some issues with the high and low range. Suspicious my problem may be with a sensor on the drop box somewhere. Unsure as to which sensors do what. Can somebody clue me in or have a diagram?
See more
Top