• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Recent content by Geoff Lott

  1. G

    genie s-60

    I’ve never seen these on the 2011...not saying they don’t exist...the tensioner is just that 17mm bolt and the 8mm Allen bolt with one pulley and brackets is all I’ve seen..I’ll keep my eyes open though..must be old machine...you got a picture??...everything I’ve seen is the orange tach wire...
  2. G

    JLG 60H no function from dump valve #2

    Look up manuals on JLG website and go to the parts manual for it and find dump valve location I believe it’s on the right side of the manifold and pull valve out.. I believe there two valves correlating to it...and you’ll know which one it is...JLG had a campaign on them at one point because it...
  3. G

    2004 genie z-45

    FOOTSWITCH good??
  4. G

    genie s-60

    Yea first thing always to check on 2011 Deutz with your symptoms are the belt as the machine gets its tachometer signal from the alternator so if belt breaks machine cranks but no RPM signal is fed to ISM so engine shuts down...then move onto measuring HZT output of alternator
  5. G

    engine distress for JLG 450 AJ

    Engine temp sensor??
  6. G

    Genie 1930 electrical issues

    Did it resolve the issue??
  7. G

    Gehl Telehandler

    Had a old Gehl do that to me...what does the transmission display say??...should be a digital transmission display used to protect transmission if low voltage issue occurs..more than likely bad shifter...the little rubber type button thing on the end of gear select is nothing...it’s a generic...
  8. G

    JLG 60H no function from dump valve #2

    Pull correlating valve out of function manifold...they have a problem with blowing the snapring and coming apart...you’ll know it when you see it..issue NO FUNCTIONS
  9. G

    Skyjack 3219 weak drive

    I’m in agreement with the brake release knob...
  10. G

    Genie Joystick Controller - Dual Axis intermittent

    Recalibrate joystick...and see if problem goes away... GCON key switch to platform In platform pull e-stop out DO NOT PUT FOOT ON FOOTSWITCH *To joystick being calibrated** Joystick forward 6-7 seconds Back to center for 2 seconds Joystick backwards for 6-7 seconds Back to center for 2 seconds...
  11. G

    Genie GS-1930

    Check the harnesses running from pothole switches...also the pothole switches themselves for a audible clicking....the elevation switch in center of machine by tilt switch as well....
  12. G

    Genie z45/25 won't rabbit

    You just answered your own question ....if you moved the boom up and back down and it went into rabbit at least once...then lift boom and go to rear of boom and check your limit switch at rear of boom...there is also one for fly in and out...if you have one that is sticking or not good it will...
  13. G

    1999 Genie TMZ 50/30 Outrigger Failure

    Ill assume this has the updated motor controller....ALL THESE CHECKS ARE WHILE HITTING A FUNCTION...(just yellow button will be good enough) first off what voltage are you getting on blue wire coming out of motor controller plug (#1)...should be DC batt voltage 22-25v.....then check white with...
  14. G

    Genie s45 intermittant glitch

    Check both estop contact blocks at ground and platform for input and output voltage and fluctuations when issue occurs
  15. G

    ZF MS-T3060 axle seal

    But if we are talking about the inner axle seals and the inner hubs seal...no special tools..AT ALL...just the pain in the butt king pins....
See more
Top