• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Recent content by driveshed

  1. D

    Komatsu KC30

    Hi guy's it been a long time , hope everyone is well under the Cov-19 . I've got a Komatsu KC 30 and I hope someone here has run accrosed the same problem. The unit has not hydrualics won't drive and no loader. I have bypassed the seat switch , and hook up a temp wire to put power to the brake...
  2. D

    Komatsu CK30-1 problem

    I know this is a old post but did you find out what was wrong with the KC 30, got the same problem
  3. D

    Genni Lift starting problems

    i will take a look here today,
  4. D

    Genni Lift starting problems

    Hi Newfiedan the number that is on the DIS module Is F5JL-12A297-DA. the engine I have is Model LRG4231-6007-B. the machine serial # is Z-45-003938 if you need anything else let me know, I don't see a plug near the heat shield
  5. D

    Genni Lift starting problems

    I dont know what mean by a gcp display and where would the diagnostic connestor be. My unit is a 1996 , let me know and I will double check the grounds again
  6. D

    Building new shop need some info

    hey Cat 320 The way I did my floor was I took out about 24" of soil and work up to 12" with starting with 6" 3/4 crush limestone and then 6" 5/8 stone and compacted it for about a day. My outside of my floating slab is 18" deep, 24 " at the base and then comes up on a 30degree . I...
  7. D

    Genni Lift starting problems

    Thanks Willie I will keep you posted on the turn out. Dave H
  8. D

    Genni Lift starting problems

    Hey Willie Yes I think now we are on the right track with this unit ,I don't what to buy a whole lot of parts if not needed. I always say it better to repair that replace. there is one other problem with this unit , it does not go into 4 wheel drive . I know that the 4 wheel drive only work in...
  9. D

    Genni Lift starting problems

    Hi Willie well Iam wait to get price on new ign module, today a buddy of mine come over and we were looking at it and he is pretty good at ign stuff and he started to play with it and before I knew it ,it was running. what he done was put resistance on the two wires from the DIS to the crank...
  10. D

    Genni Lift starting problems

    Hi Willie well today I got some time to do a little more testing and I found that the DIS is not put 12 to both coil wires only one and with the spark test hook to # 1 cly it is only firing about every 6 to revouation so i think my problem lies in the DIS . Thanks alot Willie for your time Dave H
  11. D

    Genni Lift starting problems

    Hi Willie When the wires that go to the choke ,if I hook to the choke the volts there when cranking ouer is 4.25. If I remove the wire the volts are at 11.5 when cranking. I will try run a wire let you said and I will see what happens Thanks DaveH
  12. D

    Genni Lift starting problems

    hi Willie well I did some more test and on # 8 I have full volt when I unhook the starter and when I hook it up it drop to 11.8 volts . and it is the same with all the ing circits they drop ,so I think and I may be wrong the starter is drawning to much and is robbing it from the eng module, I...
  13. D

    Genni Lift starting problems

    Hi willie I time to start testing and yes # 8 has 11 volt with the choke unhook if I hook the wire up it drops to 4.25 volts so with the wire unhooked it will give spark on #1 somtimes an it would try to start .
  14. D

    First service truck could use some advice

    Hey Joeyz One thing to keep in mind is how much are you going to put on the truck, I bought a nice F350 a 96 that only had 37000 KM on it when i got it . Now 6 yrs later I am going to get a bigger truck cause of the wieght that I am carrying. The biggest down fall to this F350 is it is a gaser...
  15. D

    Building new shop need some info

    here is pics of the construction of it the JCB was A life saver
See more
Top