• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Recent content by davecampbell

  1. D

    Deere 700H Codes!, Codes!, Codes!

    I have a 700H with same code and same 4 dashes for trans temp. I've also had to drill the vent in my fuel cap. Either there is a pattern here or I've bought your old dozer.
  2. D

    komatsu D41P-6 transmission filter

    my dozer calls for a 23S-49-13120 filter which komatsu no longer supplies. I tried an oil filter company in oklahoma city and none of their suppliers could cross reference it either. komatus sells a $500 upgrade kit to upgrade to a $117 filter that they still sell. Is that my only option?
  3. D

    Esco ultralok teeth

    Im near Seminole. Im about 2 hours west of fort smith. can you take paypal and put them into a USPS flat rate envelope?
  4. D

    Esco ultralok teeth

    Loks like the bolt in retainers are on back order :(
  5. D

    Esco ultralok teeth

    thankyou. Worked the excavator 7.8 hours today and lost 2 more teeth!
  6. D

    Esco ultralok teeth

    ive unsuccesfully searched for bolt in keepers for these teeth
  7. D

    Esco ultralok teeth

    Id like to get bolt on, especially if I can stop losing teeth.
  8. D

    Esco ultralok teeth

    I initially had loads of problems with them coming off. I figured out that someone had put u40 teeth on a bucket that called for u35. I still lose them occasionally but its at an acceptable level now. Ive had a couple of jobs that I had to dig though sandstone and I wore them dow to where it's...
  9. D

    Esco ultralok teeth

    I feel Iike esco is robbing me. I'm not used to a $1000 bill because my reeth are worn out! What are my alternatives? Can I just weld replacement teeth on? Is it better to have the bucket converted to different teeth? Maybe just buy a different bucket?
  10. D

    case 888 suddenly lost power

    Traded off the case and now I have a komatsu pc210
  11. D

    komatsu pc210 VGT turbo 6.7 cummins

    Worked it for 5 hours today with no issues so I think the missing stud was the issue. I think Id have found it sooner if I wasnt perplexed by it only doing it hot.
  12. D

    komatsu pc210 VGT turbo 6.7 cummins

    I was still getting boost around 22lbs cold and 18 warm. You dont think a 3/8 hole is a serious enough leak to cause my problem?
  13. D

    komatsu pc210 VGT turbo 6.7 cummins

    The intake heater on this motor is located after the intercooler and before the EGR. Its pressurized there so it shouldn't suck dirt in, should blow it out. It was blowing air out when I found the hole. Testing it cold I got 2 lbs more boost than prior. Im anxious to test it warm to see if this...
  14. D

    komatsu pc210 VGT turbo 6.7 cummins

    I found a missing stud on my intake heater. With the insulator missing also its almost a 3/8 inch hole. Hopefully that is my boost leak. If so, it only showing up when warm still is confusing to me.
  15. D

    komatsu pc210 VGT turbo 6.7 cummins

    thanks Ill try to get those tomorrow
See more
Top