• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Recent content by chansey

  1. chansey

    I need a repair manual for a Scat Track!!

    Scat Trak apparently used just about any engine that would fit in the machine. I have a 1700C that had a Perkins engine. I have seen Kabota and Izusu as well. I retrofitted mine with a Cummins 4BTA. Fit great and has plenty of room. Fab'd a flywheel housing mounting plate and added a...
  2. chansey

    Case 621B XT Wheel Loader

    OEM engine fail was lack of oil and overheated. Things look good. I'll work on this in the spring. Right now the snow is an issue even getting to the unit. Thanks for the inofo Paul
  3. chansey

    Case 621B XT Wheel Loader

    It's time for me to ask the experts on what I should do with my dead loader. Engine seized on my 621B XT wheel loader. It's a 6 cyl CHN 590 rated at 138 HP with a VE injection pump I have a rebuilt 1993 Cummins 5.9 with HP rated at 160 HP. My thoughts are to use the 1993 Cummins engine long...
  4. chansey

    Trojan 1500Z Hydraulics

    My pump is on it's way out, slowly loosing hydraulic pressure and lift capacity. Need help locating a replacement pump The the front shaft bearing had failed and caused the gear sets in the first two sections to woble and tore into the housings. No go with Minpar or Deluxe-- not available...
  5. chansey

    Discussion: Dana/Spicer 3 Speed Powershift

    I tend to agree that this pump is not unique or special. There are numerous 3 stage pumps available That have capacities similar to the one being discussed. The two outer pump gears are the same. The center one is much smaller. The gear drive is involute, however it is available. I need...
  6. chansey

    Discussion: Dana/Spicer 3 Speed Powershift

    This is the pump drive from the transmission. The three washers do not belong on the shaft. Moves the seal out so that it does not function. Bearing and seal are off the shelf at Parker. Only the shaft portion of the bearing was found. Drive housing and first pump stage. Due to the...
  7. chansey

    Discussion: Dana/Spicer 3 Speed Powershift

    The coupling drive gear bearing and seal were completely torn up. The front cover and plate were removed for inspection. When I purchased the loader, the 4 bolts holding the pump housing to the transmission were off completely. I believe that they were troubleshooting the hydraulic leak into...
  8. chansey

    Discussion: Dana/Spicer 3 Speed Powershift

    funwithfuel Thanks for responding ..... Things have changed and for no reason at all, but to answer you questions, the brake is a dry type and is an external drum mounted outside the transmission. As for the pump, I have no faith in it at all. Because of the bearing failure, the was some...
  9. chansey

    Discussion: Dana/Spicer 3 Speed Powershift

    I have a 1989 1500Z Trojan Loader that that has a Dana/Spicer (Clark-Hurth) 3 Speed Powershift transmission and the transmission is being overfilled with hydraulic fluid. The overfill is about 4" above the full mark on the dip stick and then hydraulic fluid starts running out the bottom of...
  10. chansey

    Ford A-66 specs and parts?

    Can anyone tell me if the Ford 401 is a SAE #2 or SAE #3 flywheel housing. Repowered a Trojan 1500Z with a 4cyl Cummins 4BT 130 HP ...... Lots of power
  11. chansey

    Case W14 loader engine

    Do you know how much the 4BT is going to cost ?? Missed one in Texas for $250. I'm currently building 2 each 5.9 6BT's but I have people asking for the 4BT's all the time. I purchased mine in WI for $1500. It was totally complete. Fired it up before it was installed.
  12. chansey

    Case W14 loader engine

    Tinkerer, It's not all that bad of a job. I used a 1973 Ford pickup radiator and made the support brackets. Used off the shelf hoses to connect everything up. Bent a piece of 8 GA. wire and took it to the auto parts store and found the hoses I needed. As for engine brackets and mounts, the...
  13. chansey

    Case W14 loader engine

    I forgot to include the dims for the FH housings The adapter ring I machined. Drew it up on AutoCad and downloaded to the Plasma for the ring portion Used plasma to spot center of the holes. Tried hand drilling and FAILED ..... then used Bridgeport mill with DRO and fit perfectly.
  14. chansey

    Case W14 loader engine

    It's been almost a year since your post. Have you done anything with your Loader? A 4BT 3.9 will fit and bolt up if you have a #3 flywheel housing.
  15. chansey

    Trojan 1900Z Transmission issues

    Do you know the manufacturer for the transmission ? The 1500Z and 1700Z had the same transmission, Powershift/TC 3 speed. The 1900Z and 2000Z had different trannies over the years, so a Manufacturer and Model will help. Had an older 1500Z (1980) that had an Allison with the same issues as...
See more
Top