• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Recent content by bobbyblades

  1. B

    bucket tooth

    anybody got a tool they can part with
  2. B

    bucket tooth

    yup 23 1 1/2 x 1 3/4 at 6 inch those are down to 4.7 inch long i could get new set but 70 for the tool ?
  3. B

    bucket tooth

    580k phase 1 lost a tooth
  4. B

    bucket tooth

    what is the part # or size i need
  5. B

    580 k gear grind ?

    i went out seperated the brake pedal pin right side more grind than left and one pedal works better than the left ... brake disassembly on the list MAYBRE A SPRING BROKE OFF AND IN THE WORKS
  6. B

    580 k gear grind ?

    580k phase 1 getting a gear grind when i let off power and brake sounds like when you shift a manual tranny and miss the gear a bit grrrr/pop . comes from right under the floor it only lasts a half second it happens in any gear forward and reverse most...
  7. B

    another flat

    wrinkle ?? how ? tires not my specialty what did i miss
  8. B

    another flat

    no hole in the sidewall no hole anywhere but tube is trashed cause i drove on it to long flat and ripped the valve stem looks more like a tear about three inches up from the rim edge oh well
  9. B

    What do you think about this Case 580 for sale, needing repair?

    go to your local town road/highway dept inquire on a mechanic for on the side work they do work during the slow days or winter paid 10 for mine and put in 5k but for all the stumps and logs i pulled dug a pond leveled the property it was worth the expense and bet i can get at...
  10. B

    Case 580se GLAND NUT won't budge!!!!!

    hey if heat it up make sure the oil is out it will never get hot enuff with hand torch the oil acts as coolant are you hammering it out from the other end / is see the mushroom the other end with the clip or lock pin removed
  11. B

    Case 580se GLAND NUT won't budge!!!!!

    i had no screw too but found the hole the screw top sheared off leaving the rest inside i drilled it out and she screwed right off sawzall and or grinder the pin you got three spots to chop it get many blades . pin inside take a beating or got bent and gets scored to point ...
  12. B

    What do you think about this Case 580 for sale, needing repair?

    simple just poping the nut with a breaker bar and pipe a bitch
  13. B

    580k shuttle ouyput shaft seal

    ok so i got the output seal dripping some can i get the seal out by prying it out with just the yoke off or do ineed put that tail off too with the six bolts and do the paper gasket and do i need to drain all oil or just let it spill out during repair and top off later seal...
  14. B

    Piston nut won't budge - broke the ratchet - pics

    heat heat heat / but lock tight and nylon ..overkill? wait if you heat nylon will it melt? make it worse ? weld a socket to a bar then to 1 1/2 cheaters? point it up and hook it to the pickup truck with chain :notworthy
  15. B

    555E hydraulic cylinder pin removal on stabilizer

    set the foot pat on solid surface get the wieght off pin . worn grooves on pin catching bushing?. cut off whats sticking out and go the other way ? looks like the left side got bent out so your bore thru is off and pin hangin up / could be the groove of the retiner clip even catching...
See more
Top