• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Recent content by bartelbe

  1. B

    Case TV380 Moves backwards on its own, STOP light lit up

    You can check voltage at sensor connectors but If that was a issue you should get a different code. Gary posted above the pin locations at the sensors for the signals references. You should be able to trace these back to the ucm on you schmatics for which connector and what pins are the...
  2. B

    Case TV380 Moves backwards on its own, STOP light lit up

    if was joysticks then 2 things should be also true, 1 joynu in display when trying to release parking brakes, and 2nd should be able to isolated the issue by changing the pattern from h to iso. Since your getting the code for both and the the bucket then checking the signals back to the ucm...
  3. B

    Case TV380 Moves backwards on its own, STOP light lit up

    Replace the sensor, 2 possible causes ,sensor or wiring. sensor could very well be sending false position so ucm is energizing coils to try and center the swash plates. and honestly the sensor is cheaper and hell of a lot easier to change then the harness.
  4. B

    Code

    Dont think theres a code and i cant remember exactly if the series 3 400 had the option , i know some you had to use the EST software to go into the display but you can only increase hours not roll em back so if you made a mistake putting hours in on a new display it was a expensive oops while...
  5. B

    Case 1840 leaks oil from flywheel housing

    no need to take the pump apart the shaft seal is retained by a snap ring simply remove and drill a small hole into old seal insert a screw and pull it out. inspect the shaft for any groving if not to bad install a new seal and away ya go. part # for seal is N14103 which will proabley supersed...
  6. B

    Case DL450 ?

    Ya right , I seriously feel sorry for the person that buys that, Case has great ideas but poor engineering. There alpha skids have been a nightmare for the majority of owners and took them years at the cost of the owners to start and correct some of the issues, I could list most of them but...
  7. B

    821c

    Lets see if i can help. For forward gears the trans needs 2 solenoids powered, and same goes for reverse, so 1 st gear forward, forward clutch "KV"and K1 solenoids are activated 2nd gear would be KV and K2, 3rd KV + K3 reverse is simaliar but instead of forward clutch "KV'' Revere clutch is...
  8. B

    Case 688 hydraulic problem

    Pull the hydraulic filters and check for metal will save ya a trip out from the dealership and it will be one of the things the tech does. if ya find metal then hook some gauges up to check pressures,unfornately case no longer offers pumps for this old of a unit.
  9. B

    Case 321E Deutz Engine Starting Issue

    Looks like your on the right track with checking glow plugs, the 321E is a b*****d machine. but anyway on to my 2c , This makes me believe of more a cylinder heat issue since she smokes on cranking and cracks off with a little sniff of ether, When it was new the glow plugs proabley werent as...
  10. B

    case tv380 won't start

    With ATS in display there is a fault. Sounds to me like the dealer is just throwing parts at the problem which I can't blame them since cases support is **** poor which eventually starts with FPT lack of what the hell there doing. Emission control units have been in production for some time with...
  11. B

    430 Case skid Steer runs rough

    Most I have seen tend to exhibit rough running at high rpms when engine temp is at operating temp. When cold they run as should but this is due to the ksb affecting timing. So have em check timing spec I believe for non turbo'd is .95 mm at tdc and 1.27 mm at tdc for turbo'd . Also would be a...
  12. B

    430 Case skid Steer runs rough

    No the solenoid is not the issue , All the solenoid does is advances the injection pump timing. Once the engine temp reaches a certain temp power is taken away from the solenoid which then retards the timing. The dealership fix which i am well versed in is to remove the pump and send it to a...
  13. B

    2012 case sr200 --- a/c controls inop

    I think your looking at the wrong relays i am referencing, Behind your head there a louvered plastic cover with 2 knobs on each side that allows this louvered plastic covered to be removed to access the hvac filter, once you remove the filter which is done by' also turning 2 stupid plastic...
  14. B

    430 Case skid Steer runs rough

    The fuel advance the dealer is referring to is called the ksb solenoid, if this is the culprit 95% of the time it would run great when cold, another easy test is when it starts to exhibit the problem jump 12v to the solenoid and see if the engine clears up. Also if anyone ever had the injection...
  15. B

    RC 30 not charging

    You are correct the alt diode if installed backwards will prevent the alternator from charging, make sure the diode symbol on the diode matchs the symbol in the location it plugs into. Assuming both symbols are still there.
Top