• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Recent content by BAD5oh

  1. B

    Wa250-L3

    E03 code. Won’t move forward or Reverse but dash does indicate when lever is in F or R. Is there any way to pull codes without any software or does a dealer have to come out?
  2. B

    s205 aux valve controls

    Checked that. I'm getting the constant power. Ignition power and a good ground. So I bypassed the whole 14 pin kit and plugged it back in for only the 7 pin plug like it came when we bought it. Same results. In the 7 pin plug I get the 2 power wires and a good ground. No functions from the thumb...
  3. B

    s205 aux valve controls

    I am not getting power out of the plug to the solenoids. With it plugged in, I even traced all the wires before the plug on the machine side. Only one constant power. Nothing else. When I try the functions.
  4. B

    s205 aux valve controls

    It's been working on this machine for 5 seasons. I installed the factory kit for the 14 pin plug. Was a plug and play kit so no actual cutting and splicing wires. Last season these functions stopped working once. I parked it and the next morning everything worked fine again and no issues rest of...
  5. B

    s205 aux valve controls

  6. B

    s205 aux valve controls

  7. B

    s205 aux valve controls

    It only has 12 male pins in the plug. I cleaned it and I can see where 2 more would be. But on the blower side it only has 7 female pins out of The 14. And those 7 do not line up to the 2 missing male pins on the machine side. There are no signs of broken pins and this is the only attachment we...
  8. B

    s205 aux valve controls

    2010 s205 high flow. foot control machine and using a 12 pin plug on the aux hydraulics. Running a Erskine snowblower. The blower works fine when you hit the trigger. Everything there works as it should. Looking at both joysticks, the 2 inner buttons on each side that move up and down with your...
  9. B

    wa320 3rd function for plow

    Want to install a diverter valve in a 1995 komatsu wa320 for a snowplow. We have diverter valves tied into the curl lever in a couple other loaders with a push pull cable that work well. I came across electric diverter valves that look pretty simple and smaller. Most I'm finding are rated for...
  10. B

    1986 komatsu wa350 trans

    had an issue last year with machine not moving. Found broken power wire going into solenoid bank for trans. machine worked fine for a couple storms. Now all of a sudden it moves here and there. meaning goes into gear when you release parking brake. and sometimes it won't. Also when plowing...
  11. B

    1998 international 4700 brake issue

    1998 international 4700 with juice brakes. new master cylinder. New front calipers. New front rubber brake hoses problem is when driving the brakes will slowly apply themselves without touching the brake pedal and eventually stop the truck. Only way to move the truck again is to release the...
  12. B

    98 international 4700 brake booster

    1998 international 4700 dt466. Having issues with the brake booster. Brake pressure light is on. With key off, press pedal and nothing at all. Hard pedal and backup motor does not come on. Turn key to on position and backup motor comes on. Start engine and motor does not shut off at all...
  13. B

    L90C third valve

    Have a L90c with no 3rd function. There is a 3rd valve already set up but there are no lines or pilot valve in the cab. I read a post about a similar situation in here for a L180D. My local dealer said there is no kit. For kicks I gave him the part number posted for the 180D. He told me its a...
  14. B

    1986 wa350 won't move

    parking brake solenoid? I crawled under the loader and the solenoid valve was not applied and the pads were not squeezing on the disk. Or are you talking about a different solenoid? If so, where would it be located?
  15. B

    1986 wa350 won't move

    Plowing this morning. Driving up the street and all of a sudden the loader revved up and stopped moving. Clutch cutout switch didn't do anything. Cut the wires and still nothing. Parking brake not applied. Oil level in trans is good. Filter has less than 100 hrs. You can feel it go into forward...
See more
Top