• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Recent content by Align Machine Company

  1. A

    Doosan DX480LC Boost PSI

    Looking for high idle boost pressure for DV11.
  2. A

    Perkins 2300 Manual

    Hi Friends, Hope I am posting in the correct spot, as I did not see a chipper channel. Anyway, I am in search of the Perkins 2300 4cy engine manual. Serial is not legible and all I can make out is 5701/2300 Perkins. Thank you
  3. A

    Cat 3046 Gurus. Oil consumption question

    The number provided is a CAT reman number
  4. A

    Cat 3046 Gurus. Oil consumption question

    Buy a cartridge. Agree
  5. A

    Cat 3046 Gurus. Oil consumption question

    There should be almost no vertical movement of turbo shaft. There will be a very slight amount of plunging movement. That picture looks like your turbo shaft seals are pushing oil to the turbine side of turbo
  6. A

    Cat 3046 Gurus. Oil consumption question

    How is the exhaust dripping but the turbo exhaust turbine dry? Do you have the serial number of the 315L? I can look up in SIS.
  7. A

    Bobcat 743 Spool issue

    if the valve has load check poppets, they could possibly be hung up by debris... I would ensure all spools are centered, then disconnect the lift/lower output function lines (leaving valve and going to cylinder) and connect a enerpac pump with a gauge and slowly pressurize the spool, this should...
  8. A

    Bobcat 743 Spool issue

    Are you familiar with micro leak testing?
  9. A

    Bobcat 743 Spool issue

    Spools should not be tight in their respective bores, they are essentially slip fit with only oil film making up the clearance. Did the spools have any wear or marks on them? Did you ensure no internal leakage between valve sections? Lift spool could be receiving all or most flow resulting in...
  10. A

    JD 315 Crank no start

    Forgot to follow up, the engine has low compression. Customer does not want to fix... Going to auction.
  11. A

    JD 315 Crank no start

    Pulled intake, no broken springs on pumping units. I can see the rack moving in block, it doesn't seem it's moving as much as the shut off solenoid is moving at the cover end? No bent push rods either....
  12. A

    JD 315 Crank no start

    Ok, I'm here now. Pinching return did not help. I pulled front fuel rack cover and it seems the rack is moving... Radiator so close had to get a accurate measurement. There is a lever that the fuel shut off his banging and staying in one position, but I can move it back to neutral? The magnet...
  13. A

    JD 315 Crank no start

    Heading back tomorrow morning, snow delayed my visit. Will report back.
  14. A

    JD 315 Crank no start

    Engine cranks strong to 320RPM, confirmed on display while cranking. Did not pinch fuel line but did pull a slight vacuum on return while cranking and had fuel. Ether was barely used, I understand it's constraints.. It was used to test for pop off. I do not know if it has been used in the past...
  15. A

    JD 315 Crank no start

    Read through what I could find on here about this engine but it was old so I started a new thread. I got a call today to check out a 315 for no start, I am second to this as the dealer put a starter and battery in it and told customer it was not worth fixing... The machine has 487 hours on it...
See more
Top