• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Recent content by 74inchShovel

  1. 7

    I have 1835B Case Skid Steer with 188D engine-fuel uptake question

    Hey Tim Couple things. First, you have to use a diesel specific inline pump, typically rotary vs diaphragm action used on carbed motors. The reason being is you don’t ever really build pressure the pumps runs continuously and what fuel is not used is returned to the tank. I had a couple...
  2. 7

    09 PT 30 starting issues ??

    I think that’s it. Get the engine to turn over and fuel is next
  3. 7

    09 PT 30 starting issues ??

    Looking at your filter pic, precleaner is clearly visible right behind it. The bottom of plastic has a hex cast into it, I think it’s 1 1/16”
  4. 7

    09 PT 30 starting issues ??

    Ok, looking at your picture you have two reds (battery hot) below with a wire on top. In between separating them is a small rectangular block of plastic. The terminal for white wire is to the left, towards engine of plastic block. Got a mirror on a stick? So looking at solenoid only it’s...
  5. 7

    09 PT 30 starting issues ??

    Cant get picture to post . I could get it to you email, maybe PM it? Long stories short, the white wire on my machine is power to starter solenoid, hot only when keyed to start position. Use a trouble light, check your white wire to see if it’s key hot. The fuel precleaner is directly behind...
  6. 7

    09 PT 30 starting issues ??

    Ok, that’s the primary filter. Will try to get pics of precleaner for fuel and starter wiring
  7. 7

    09 PT 30 starting issues ??

    I think there might be two things going on. First thing I would do would be to verify when you go to start starter solenoid is getting battery voltage. I would make sure battery is fully charged then load test at an auto parts store. It might make good surface voltage that collapses under any...
  8. 7

    CAT 247b No Start Issue

    Do you have 12.5 from battery hot to frame? Take apart all grounds and clean. A bad ground can pass the micro current that will allow a volt meter will read as 12.5 but when you try a much higher amperage it won’t go.
  9. 7

    Tak TL120

    Good morning. That machine does not have pins that engage, but a brake pack that is disengaged by hydraulic pressure. The fact the controls go dead is a huge diagnostic tip, these have what is termed “pilot pressure“ ran to them, the controls send this pilot pressure to the actual valve and it...
  10. 7

    My old Skid Steer has started to start then quickly stall.

    Back in the day I was working on a case 480 backhoe, same 188, or 207 motor. Same problem. After much head scratching, it turned out that there is a rubber gasket/diaphragm inside the injection pump that starts to rot out over time. The little pieces would be drawn into into a passage inside...
  11. 7

    SVL-75 track trouble

    Avoid counter rotating- do three point turns whenever possible Watch angle of attack going up slopes, much better to go straight on as opposed to going up at a shallow angle If the grounds has rock, make a conscious effort to keep material out of UC The Tak I used to own was bad at this as...
  12. 7

    CASE 1845c Restoration. Follow my progress!

    Great platform to start with. (Simple, rugged and dependable) Funny how those three go hand in hand. Best engine ever put in a skiddy, imho. Known to go 10k+ hours before rebuilding. Made by a major company for many years, parts should be no problem. Looking forward to watching your progress !
  13. 7

    DAVIS Trencher

    Looks like a Wisconsin TJD,had similar in a Ditch Witch many years ago. Your chain is set up pretty aggressive, farm dirt you’ll be ok, any type of rock you may want to narrow it. Am I seeing it correctly, the outermost hydraulic pump only has one line to it, is one missing?
  14. 7

    TL130 with a miss

    Can you force it to miss by sending hydraulics into relief, bucket curl all the way back, lift all the way down? If so, have someone in the cab doing this while you crack high pressure lines one at a time at the injector to see if if there is one injector that when the high pressure is cracked...
Top