Lull 844 644 Owner Operator Manual now avail on pdf

[joestewart]

You can buy a manual on ebay for an ungodly sum or I can email you one for free. PM me your valid email address. Post some photos of your machine and tell us about any problems you are having. J. Stewart

 

[HillbillieAcres]

1989 Lull 844

Hi: Joe

The 1989 Lull 844 paperwork is being processed @ US Customs
& then the Trucking Home is my next Challenge

I will Post some Photos @ a Later Date when the Machined arrives Home

Regards
Myles
gemini@gemini.ab.ca

 

[CarpenterRick]

Hello all,

I have a 1999 Lull 644D-34 Highlander with a leaking boom extend cylinder. After pricing a rebuild of the cylinder I have decided to take it on myself. Has anyone rebuilt this cylinder? My main concern is that the local lift repair shop says that both counter balance valves must be replaced. They also said seal kits are not available for the valves. Can anyone shed some light? I am just a couple of tips/ tricks away from getting started.

Thanks in advance,
Rick

 

[joestewart]

My boom extend cylinder leaks also, but I have not mustered up the gumption to rebuild it (I can tolerate the leak, for now). When the time comes, however, I will do it myself following the procedure in the manual. Did the local lift repair shop tell you the reason why they recommend replacing both counterbalance valves? On my machine (circa 1990 644), those valves are not servicible (they cannot be disassembled, and there is no "rebuild kit" for them). They are also very expensive (I think I recall them being about $550 apiece). Question: If you extend your boom skyward and shut off the machine, leaving it in this position for an extended period of time, will the inner boom slowly telescope back into the outer boom? If it holds it position over several hours, doesn't this suggest that the counterbalance valves are still good? Is it possible that the repair shop routinely replaces them for liability reasons? What city are you located? I'm in Lafayette.

 

[CarpenterRick]

Joe,
The local lift repair shop said that both valves must be replaced...I am sure it is mostly a liability concern as you stated. It holds position just fine. The cylinder actually started leaking (along with cylinders on other equipment) after that hard freeze last winter. The shop manager did say that they may not be able to re-insert the piston with out removing at least one of counter balance valves.

According to my estimate, the valves are 1200 for both including installation. That is 200.00 more than the mob/ demob and seal repair/ replace. I am sure there is a trick to this. I noticed that you said you will follow the repair procedure in the manual and from what I have read above I may be able to find one on this forum. Any suggestions on where to find the manual for my machine? Know of anyone on this forum that has performed this service on a LULL 644D-34?
I am in Baton Rouge...actually just finished a custom home (about a year ago) in Youngsville.
Just a couple more months for LSU football...
Thanks again,
Rick

 

[Kara21]

Hello, I was wondering if you would be so kind as to send me the manual? My boss has been trying to find it for about a week and a half now and he would love me if I was able to get it for him. My email address is Kara_18_1990@yahoo.com I would gladly appreciate it!

 

[Macool]

644 highlander manual. Ive checked the jlg site link. It shows no manual. Does anyone know where to get one or send me a pdf copy. Maccol

 

[joestewart]

644 highlander manual. Ive checked the jlg site link. It shows no manual. Does anyone know where to get one or send me a pdf copy. Maccol

Is your 644 an early model? If so, I have a some manuals. What year was your Lull made? I'll need an email address in order to send anything.

 

[Macool]

lull

Is your 644 an early model? If so, I have a some manuals. What year was your Lull made? I'll need an email address in order to send anything.[/QUOTE

It's a 1996 model. Email is cwood@rockettinc.com.

Thank you for all the help you give people here. I see it all over the boards.

 

[RogerDon]

Lull 644 Highlander 11

I need a copy of the operators/service manual for the Lull Highlander.

Thanks

Roger Southerland
Roger5050@hotmail.com

 

[hodgesfarm]

I found several manuals online for the 844C and 644E and 644b but I need the manuals for the Lull 644D-34. Could I please get the copies from you. I am having a problem blowing fuses and the circut panel started to smoke. It quit running. When we started it back up, it wouldn't move. I could really use some manuals to troubleshoot the problem. I have had three mechanics work on it and they cannot figure it out. Thank you so much!

Anne
HFEhodgesfarm@aol.com

 

[carlos sanchez]

hellow .my mame is rick and I am trying to wire damage wires to a lull 644d-34 ser # 99al25w24-651 please if you have schematic .wiring for cab to engine and trany thank you my email is csan5299@yahoo.com

 

[k-vanman]

looking for pdf file service manual for Lull highlander II 644 with a JD engine.

Having an power train issue, shuttle builds air presure? starts to move then loses power, shut it off and the vent on the shuttle releases air. do I have to rebuild the tranny? or do I have air locked in it some where? can any body shed some insight?

 

[joestewart]

k-vanman, that's a highlander II? A 644? Not sure what you mean in the description of the problem. Can you clarify? I can help you with the pdf of the manual, if it applies to your machine. PM me if you prefer.

 

[gdonovan]

If you could be so kind, I'm looking for any operations or service manuals for a 68-72 vintage Lull 400 / 7C series lift with a Chrysler 225

Even an early 644 manual might be of help as it looks like the control panel is the same.

Gary

speedydaytona@yahoo.com

 

[Lik2waterski]

Hello, I am new to this forum and have owned this lull for a couple of years now. I love it. I would like some manuals if anyone has any for my model.
Its a 644B-37 SN-97V12N21-823 My email address is lik2waterski@yahoo.com
Thanks for any help you guys can provide.
Travis

 

[joestewart]

Here's the link to JLG downloadable manuals. Is there anything here that will apply to your machine?

http://csapps.jlg.com/OnlineManuals....jlg.com/en-US/Maintenance.Repairs.html&link=


My manual does not cover the 644B

 

[Lik2waterski]

Thank you, JOE!

 

[carmen]

I am looking for the operation manual for a Lull 644 Highlander II. I am told that there is supposed to be a letter after the 644, but I could not see one on the ID tag. Can anyone help me out with this? I see JLG has a 644B available in their manuals, but mine doesn't say 644B. My email is: carmenf@elmstar.com
Thanks!!

 

[jonathanrayce]

I need a service manual for a 644D-34. Thanks.

jraycec@gmail.com