we have a bunch of these.i dont run them too often but i guess they are ok..the loader operators seem to love them..too many buttons and switches for me and the controls seem dead..like you cant feel anything..i like the old cat 950's with the long levers..seems like you could tell when you were cutting a tenth..with these new ones i'm usually a foot deep before i know it..must be getting old
No not really, in my opinion volvo loaders are not worth much.
Well, they're leading the race on wheel loaders.
Other brands investigate and copy what Volvo is doing...
Nobody will admit that in public, but under four eyes the competitors admit that Volvo is number one on loaders.(And i have discussed it with many on the big fairs)
Have a test run in same size loaders and you'll understand why.
As said by reddot556, the operators love it.
The new F models got electro hydraulics, so it needs some time in the seat to get used to.
After some hours and a right adjusted bucket levelling system you'll levell on the tenth...
Just
Have a nice day!
I've got time in volvo loaders and i was just a glad to see them go back to the dealer as i've ever been about anything, i've been in them from a 70 up to a 330. The dealer shipped them over to demo and when compared side by side with the kawasakis we had in the quarry they didn't stand a chance. It wasn't just me but all of us in the quarry had the same opinion about them, the cabs where loud, they lacked power, in my honest opinion they are not up to grade with other manufacturers.Originally Posted by MKTEF
Well, they're leading the race on wheel loaders.
Other brands investigate and copy what Volvo is doing...
Nobody will admit that in public, but under four eyes the competitors admit that Volvo is number one on loaders.(And i have discussed it with many on the big fairs)
Have a test run in same size loaders and you'll understand why.
As said by reddot556, the operators love it.
The new F models got electro hydraulics, so it needs some time in the seat to get used to.
After some hours and a right adjusted bucket levelling system you'll levell on the tenth...
JustJust ask Coalburner.
But I will say this about the 70 we had, The heated seat was nice.
It sounds to me like they wer nt Volvo loaders At all, Volvo rates it self very high on operator comfort and the ''E'' range has a lot of power at low rpm. Have known some die hard long term Cat operators converted to Volvo.
Here is a picture of brand new Volvo L350F delivered to Mill in Northwest. It has the CDC and electo-hydraulic controls. Impressive machine is all I can say.
we rented a john deere the other day cause all the volvo's were busy. this machine was about the same size as the volvo pictured. it was brand new. i loved it. no key to start..you entered a code, plus it had a tv screen in it hooked up to a camera in the back so you could see where you've been!! it was pretty cool but i'd like to see it after 2 or 3 thousand hard hours.. probably nothing would work..it did look like the bridge of the starship enterprise when you started it tho..all those pretty lights and buttons
I've got time in volvo loaders and i was just a glad to see them go back to the dealer as i've ever been about anything, i've been in them from a 70 up to a 330. The dealer shipped them over to demo and when compared side by side with the kawasakis we had in the quarry they didn't stand a chance. It wasn't just me but all of us in the quarry had the same opinion about them, the cabs where loud, they lacked power, in my honest opinion they are not up to grade with other manufacturers.
But I will say this about the 70 we had, The heated seat was nice.
"the cabs were loud" ?
.. that can not have been above 1990 years model.
(or the quality on Volvo's are muchmuchmuch better in Sweden than in US)
"they lacked power" ?
bucketsize? Unfimilar with the tp-linkage?
We have one at work I ran now and again until it's regular operator came back. Decent cab and I generally like the layout as well as that little floor switch to lock everything in for some hard digging. The bad side is that it has fairly low hours and has no down pressure and would cost an arm and a leg to fix (company ain't fixing). The ride is rough for a loader of it's size and age and I'd like more lifting power. Another bonus though is the parking brake switch is not obvious so when the boss and I were fixing the plant and let a driver load himself he could not figure it out and we laughed while listening to the brake buzzer when he put it in gear. I do like Deere though.
absolutly my favorite loader, hands down. whups a cat all day long.
SO MOTE IT BE.
the qball fan club
http://www.facebook.com/home.php?ref...id=42336642940
the qball youtube page
http://www.youtube.com/qball671
The Volvo loader is rated as about as good as it gets in the U.K. and would be the common front line bit of kit in most Quarrys/Sand pits, CAT still sell plenty of loaders in the U.K. and also are thought to be top bits of kit, the parts and back-up from these 2 Co's is of the very best, plus the kit holds a good value through out its life, sadly we do-not have J.D. kit sold with any force in the U.K. so I have no scale of how good or bad this brand is, Komatsu make some great loaders but the back-up is always found lacking, plus the parts cost is another issue, even the parts sales people laugh as they push the Bill over the counter, they also tend to rust away etc in our not to dry climate.
tctractors.
These blokes are friends of mine and they have been running Volvo loaders for years and swear by them.
http://www.krusequarries.websyte.com...usequarries/1/
There are not a lot of Volvos in this state, compared to Cat and Komatsu and while I have not operated them, I would not be too proud to own one. Our main loaders are Komatsu and we are very happy with them, but as everyone says, the backup leaves a lot to be desired.
tctractors, that is an interesting point about the rust, because even though we are in a very dry climate compared to you, our Komatsu's are rusting quite badly in the cabs around the windows.
Rn'R.
The rust factor as Rocksn' Roses has pointed out is very much a down side with the Komatsu kit, Volvo make a first class (if not the best) job of painting their equipment, so rust damage and grotty looks are not common to see even after 10 years working in Quarry's, the Dump-truck skips are smooth sided with no ribs so no rust pockets, I must admit to drive a Volvo after a CAT takes a good bit of adjustment due to the totaly different way things are set out, the Swede Machine is realy built for a different part of the World with loads of frost and a harder life, and to work not as the best/fastest shovel ever built, but to do it 7 days a week with out any snags, the fuel factor is now realy starting to hurt in the U.K. and Volvo engines are masters at only sipping from the cup.
tctractors
Around here, they liked the old Michigans, then when Volvo bought them out, they kept going with them and keep on buying them. I've heard good things about them and I can't say I've seen one broke down or in the scrapyard yet. But there are a few who like the Cats and Deeres, which also seem to go pretty good.
Haven't seen too many Kummagatsus around here, but the Suzio-York Hill quarry does have a WA900 which is incredibly huge (and an old Clark-Michigan 475, also incredibly huge).
-Austin
As tctractos say ... Volvos come from a different world then Caterpillar. The domestic market, even though it is a tiny thing for Volvo nowadays being that they are #3 in the world, is demanding.
Operators expect and demand topnotch cabs and companies are willing to pay for it cause a worn out operator is expensive due to how system for sickleave works. Hydrualic quickcouplers and "extra" hydrulic functions are standard, labor is expensive, if you can save in one guy with a shovel the price of that tilting bucket is soon saved. Also machines are expected to regulary work and perform in temperatures down to atleast -20C often clearing snow and spreading sand and salt so they are used to harsh enviroments.
Our timber industry is very important and for handling timber at sawmills and papermills Volvo and a local brand called Ljungby got the market totally cornered. I read an article last year or something about a mill trying out Caterpillars for that roll (We call it "highlifter") but they had to give up. The machines would simply not handle it. I do think there was some trouble with the front axel not taking the strain. I doubt that was cause Cats sucks .... But they tried to use them as they would a Volvo/Ljungby and it wasnt built the same way so things failed. Another configuration on the lifting equipment maybe would have yielded a perfectly good timber handling machine!
Maybe it is the same in quarrys in america. People are used to Caterpillars but a Volvo might handle differently and might need to be used in a different way to gets it worth from it.
Posting Permissions
Reply With Quote
