• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Search results

  1. O

    Does D8T LGP and XL use the same blade

    Are you seriously selling blades and have no idea what fits what as far as models?
  2. O

    Does D8T LGP and XL use the same blade

    No the 6txl xw and lgp do not use the same blade. I think they all are different
  3. O

    Lebherr LR622

    I believe the Deere tcu on a C series is around 8-10,000. Hopefully not the case on the liebherr units.
  4. O

    Lebherr LR622

    Are the TCU’s as expensive on the lieberr units as the Deere/liebherr models?
  5. O

    Lebherr LR622

    Did you figure out what the issue was?
  6. O

    Lebherr LR622

    It’s the park brake light.
  7. O

    Deere 755c 2 front idler removal.

    Ok just so I’m on same page. You mean running a punch past the threads and beating on it or threading a junk bolt in to engage the threads and beating on the bolt?
  8. O

    Deere 755c 2 front idler removal.

    Ok I appreciate it. Which one of these is the bolt you need to take off and any hints on driving it out? Thanks
  9. O

    Deere 755c 2 front idler removal.

    Trying to get the guide plates/side deals off the front idler. The outer plate has 4 bolts that go through that broke and seems only way I’m going to get the broke parts out is to remove it and get to the back side. What holds the side assembly onto the round axle the front idler has? Picture...
  10. O

    Genie Z80/60 suspected Hydrualic issue

    Have 12V around the kill switch and voltage does not change when engine dies.
  11. O

    Genie Z80/60 suspected Hydrualic issue

    When the engine dies the display stays on and says “engine speed no response”. I’ll check for power. No codes just the message “engine speed no response”. Duetz engine
  12. O

    Genie Z80/60 suspected Hydrualic issue

    After more work this morning trying to calibrate the primary boom angle sensor I’m even more confused about it. Still does the trying to kill the engine deal but when you try to go up to 70 degrees to calibrate the sensor when you get up to around 45 degrees it will shut the engine off every...
  13. O

    Genie Z80/60 suspected Hydrualic issue

    After more work this morning trying to calibrate the primary boom angle sensor I’m even more confused about it. Still does the trying to kill the engine deal but when you try to go up to 70 degrees to calibrate the sensor when you get up to around 45 degrees it will shut the engine off every...
  14. O

    Genie Z80/60 suspected Hydrualic issue

    Same thing from both controls. After more investigation today I suspect something to do with the primary boom angle sensor. Seems to be something to do with machine thinking primarily boom is too high.
  15. O

    Genie Z80/60 suspected Hydrualic issue

    Have a 2010 genie z80/60 boom lift. Was working fine and sat at a site for several weeks without use. Went to pick it up and whenever you go up on the primary or secondary boom it will kill the engine. High or low idle no different. All the other functions operate perfectly fine. Strange thing...
  16. O

    Cat D6T blade lift

    I looked back through a previous work order and had forgot I had cat do a calibration on the joystick the last time they were out for a completely different issue. Sounds like I may be calling them if it can’t be tested onsite.
  17. O

    Cat D6T blade lift

    I’m not getting any active codes that I can see. It lifts good in all circumstances other than when you get a big load on it. I’ll try to get into the monitor and see if I can find joystick position or something
  18. O

    Cat D6T blade lift

    2012 d6t. Serial number GMK00781. Anyone know what the Hydrualic pressure should be at the lift cylinders? Semi U blade and when get a big load on it the lift seems to stall out. I have pressure testing gauge kit. Thanks.
  19. O

    Deere 755c issue

    Replaced pressure switch and that took care of the issue. Thanks for the help mg2361
  20. O

    Deere 755c issue

    Replaced filter today and started with gauge on again. Still the warning light and pressure at 245-250. Ordered pressure switch to replace and hope that does it. Thanks for help so far.
Top