• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Search results

  1. T

    Cat D6 A/C

    ????00D6FUFBH0260 Has about 100 Lbs freon charge and appears compressor will not engage. All of the fuses and breakers at the right door hinge ares test good. Air flow in the cab is good. Snow flake on the A/C switch lights up when depressed. Pressure switch behind compressor has power on...
  2. T

    Mitsubishi FG25 alt wiring?

    Serial # 50257 Small yellow wire with red strip runs close to starter and harness is chewed up. What should it connect to?
  3. T

    Cat IT28F no reverse

    It is serial number 3CL01750. Any good advise on a manual? I bought one online but it ended up being a parts not service manual. Any other input also appreciated but I usually like to start with a manual.
  4. T

    RTLO16610BT2

    This Super 10 has no high range just grinds badly. Looks like a fresh reman in a newly purchased used truck. Dropped a bolt for the range fork out the drain plug hole. Can I get the back off by removing air valve on top plate or do i have to remove the top plate?
  5. T

    Claas MB 14.6L injector help.

    Trying to get injectors out of A Claas 880 Jaguar. Ordered the special tool and have been using penetrating oil for a while. It is the factory Mercedes tool but have tried it on three so far with a 3/4 ratchet. Stop a what I feel like is the threshold for the tool around 125 Ft Lb. It is the...
  6. T

    JD 6100D clutch shaft

    The center shaft pulled out. The outer tube shaft with not come out with a small slide hammer attached to a pair of vise grips. Does anyone know if it should or if the housing in front of the axle housing has to be removed anyway?
  7. T

    930G manual?

    Any online manuals out there? The real deal book looks expensive and I have to wait. We are pulling the engine. Hope it will come out with the fuel tank, charge air cooler and and the frame work around it in place. Any information on a manual and or R&R the engine is greatly appreciated...
  8. T

    Case SV185 hydraulics locked out.

    It was being driven and locked down. Shows no fault codes. Tested charge pressure and it was around 450 PSI. Checked all the fuses and swapped all the breakers. Checked all the grounds to the enable and park brake solenoids. Powered 12V to the brake solenoid, engine running and pulled it away...
  9. T

    JD 4240 hydraulic remote adjustments?

    Baler door would not stay closed. Found tractor would not maintain pressure on any of the six hose connectors. Mechanic installed new ISO conversion on one pair. No change. This coupling had not been used since the tractor was purchased years ago. Wanted more ISO connectors anyway.Then...
  10. T

    JD 320 loader locked out?

    It runs and drives but the loader arms and bucket will not move. Sounds like a by-pass or relief valve opens when the pedals are moved. Shows no codes on the display. Cleaned out all the trash around the control valves and inspected wiring. Checked all the fuses - OK. Any information would be...
  11. T

    Komatsu D31-17 power train problem?

    It will not steer left only right. When left turn is requested it grinds like chewing up a ring gear or power divider. If put in reverse 2nd or 3rd it does the same thing. Then it quiets down and right side pulls it along. What is the most likely cause and easiest way to get to it? Thanks in...
  12. T

    Komatsu 180-3

    Anybody know acceptiabe used ring gear backlash?
  13. T

    JD 320 Skid Steer oil in coolant

    At 1200RPM it pumps out about 4 OZ in 20 minutes. Some times it sounds like it is misfiring a little. The exhaust is smooth and the manifold temps are fairly equal? Valve train or injector? It has a faint sound kind of like bee bee's bouncing around in a can very rapidly. I have heard...
  14. T

    Private antique tractor special tour.

    I got a call. " Ha buddy: There is a guy in Waynesboro Georgia that has a collection of antique tractors. He is giving a private tour to the historical society. Would you like to tag along? Of course! He has decided to part with a lifetime collection. They all have to be operable for the sale...
  15. T

    Walking beam removal

    I read a post from a guy called Truck Shop. Said to use a concrete saw with a steel blade to cut them out. Set up on a 4 X 4 or 6 X 6 if I recall correctly. Had to face a giant again but this time I took a stone, or a saw for cutting them, instead of a fire wrench. The only one available for...
  16. T

    555D slow hydraulics

    Looked at this machine today: 555D with slow hydraulics. Fluid is full on both sticks. Bucket and hoe are jerky and slow. Filters or strainer. Can not read much of the data tag the parts guy wanted. Anybody have any input on that? Filter and strainer locations? Will get a tire back on it and...
  17. T

    Hydraulic Packing Supplier

    Would like to buy packing directly. It appears most of the experienced people have been replaced. Mostly agricultural and some construction equipment. Did not have a problem with the higher prices if the parts could be ordered and swap them out. Getting the correct packing is really turning into...
  18. T

    JCB436 ZF trans PSI

    ZF 4wg 200 will only move forward in 2nd gear. Displays codes B5 slippage clutch KV and B6 slippage clutch KR. Has no pressure on valve body ports for those two clutches. Could this be a relief valve or something stuck in the valve body? A link to a manual for trouble shooting?
  19. T

    Diesel Laptops

    Any experience with this company? One of their programs looks to have coverage in on road, off road, and ag. Good , fair, ugly?
  20. T

    HMF/IMT with no functions

    It is an HMF power to lift Type 1430-K3. Boom is marked INT 14/19 Series. No functions on the crane or winch work but the outriggers do. The control panel shows these fault codes at times. 1.8.0, 2.0.1, 2.0.2. 2.2.5 while holding green button. F5 high temperature light sometimes comes on for a...
Top