• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Search results

  1. S

    Hi Huffa! I would post this in the dozer or track loader section. there is several members that...

    Hi Huffa! I would post this in the dozer or track loader section. there is several members that will answer back. Info needed ripper/winch/wide-long track/inside-c frame or push beams blade and type of material being worked. Is this a MC1150E Dozer.
    • sheepfoot
    • Profile post comment
  2. S

    Case w20b - where is the air fillter?

    Climb up on the rear fender and look at the top of the hood. There should be a square plate with 4 bolts, remove the cover and the air filter top should be there.
  3. S

    Case 680L Hydraulic Cylinder Rebuild Cost

    A fare price Would be $2500.00 - $3000.00 labor.
  4. S

    Drott 40

    What series 40/40B/D/E They are not all the same.
  5. S

    Type oil to use in rubber tire loader

    The machine uses 135-H EP lube, a 85W/140 gear lube. The differentials hold around 9.5 qt each, and the planetaries 1.5 qt each.
  6. S

    Oil capacity for a 6t-590 engine on a case 888?

    16 qts with filter.
  7. S

    CASE 850 - Transmission Control Valve/Braking/Steering issues

    frankieavalanche, the brake discs stop the pinion shaft from turning, that is the reason the cutout has to drop the pressure so your not driving threw them while driving and trying to stop and or turn. The discs hold with the parking brake applied to the pinion shaft, which causes the ring gear/...
  8. S

    Ford 4500 questions

    First most all tlb and farm tractors loader edges are set by the rear axle. Tire pressure and size needs to be the same. New tire and worn out tire can change the edge angle. The block spacers at the front under the bolts that secure the loader frame should be checked also and replaced if...
  9. S

    Case 580B CK - Can Oil pan be welded to fix Rear Pivot mount....

    You can weld them but it's a lot of time and money both ways. A new pan is around $850.00 and a used front support is around $400.00. Their was around four different pans 188D/188G engine pans, one used a bolt and nut to retain the rear pin and other used a roll pin. This also goes for the 159G...
  10. S

    Compressor pumps air to disengage the fan when unloading from ship to beach or crossing rivers...

    Compressor pumps air to disengage the fan when unloading from ship to beach or crossing rivers and streams. Helps also when stuck in mud to not damage the rad core.
  11. S

    IR T30 Truck Mounted Compressor

    Our unit is a 2000, IR T30 model 2475F12.5G, info t30 2475 two stage (form SCD-761) owners manual (form SCD-748B) engine owners manual Kohler command 11-15 hp. horizontal crankshaft (form no TP-2473-C). Like Ronsii said, file shows two carb kits installed 2005 and 2009 with a note that 2015...
  12. S

    What Machine do I Need?

    I would go with a TLB first, 4wd/ 4x1 bucket/ flip over forks/ ex-tenda hoe. It may give you the most bang for your buck. You can run a hydraulic post hole digger off the hoe with a few fittings and you may even find one that is plumbed for a breaker. A good ripper for the hoe and several heavy...
  13. S

    IR T30 Truck Mounted Compressor

    I have one at work on our service truck, it was purchased at Grainger, I have the parts book and could give you the Grainger order page so you could find it on there parts site. It is a T30, seem to think it is a 12.5 Kohler around 14yrs old. Will look in the morning.
  14. S

    580 B Hydrolic pressure

    Your 580B rated pump output is 23 gpm at 2000 psi at 1900 rpm. Your loader valve main relief setting is 2200 +/- 75 psi at full throttle. Your loader with (bucket empty) full raise up in 4.2 seconds.
  15. S

    can my trailer handle it?

    Your base machine with 4wd will weigh in at 14,000 lbs., cab add 500lbs, 4x1 bucket add 600 lbs., extendahoe add 470 lbs., front weight add 500 lbs.. Weight wise your close depending on options. Your trailer type, tire and wheels would be my only concern. I would prefer a 9 ton trailer myself, a...
  16. S

    Heaping Loader Bucket Volume ?

    Your 4x1 bucket is 1 yard heaped and a little over 3/4 yard struck. Your loader max lift is around 5000 lbs. so if it will not pick your load up it weight more than 2.5 tons. Wet sand is 3,500 lbs per yd., dry loose sand at 2,700, crushed stone 2,700, earth loose mud 2,900, earth wet excavated...
  17. S

    Trackson Crazy

    That's a good looking machine for its age to find. Nice.
  18. S

    Case 586E No Forward

    You can use any thread that deals with a 580C/D/E/and phase 1 K series Your 584/585/586 C/D/E all use the same shuttle. The spring washer is more than likely broken in the forward clutch area. This requires the shuttle to be pulled out to be repaired. It will take a good hour to remove the unit...
  19. S

    Anything supposed to be in here?

    That is the top and all it had was the wire to keep the big stuff out.
  20. S

    the old 580B Question

    Your filter is a (A51463) case p/n.
Top