• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Search results

  1. R

    Ford Industrial LRG-425-EFI

    I have one of these in a Genie S 45 manlift. There does not appear to be any type of diagnostic connector I can locate. It does have one single red CEL. How do I retrieve engine fault codes?
  2. R

    JCB 214S, 1996

    Gentlemen; I do not have a serial number, although its a 1996. I was looking for a voltage drain on the batteries, removing a relay and a fuse one at a time. I never located the drain, when i was done, the tractor no longer has a transmission. Tried to verify all fuses were ok and relays in...
  3. R

    Deere 260 skid loader

    I have a 260 Deere I obtained with the engine apart. I need to order parts, not sure if the crank is standard or undersize? Does anybody have the size specification for a crank, the engine serial number is listed below. PE3029T204799 Thank you
  4. R

    Scan Tool

    I am looking for a generic scan tool. I want to communicate with Cat, Deere, Bobcat and whatever else. Anybody know of a tool that is affordable to do this?
  5. R

    Char Lynn Orbit Power

    OK, will do, thanks
  6. R

    Char Lynn Orbit Power

    I have one of these steering controls in a machine. It will steer left, but not right. Cant turn the steering wheel right, works fine left. Any thoughts, just take it apart, I suspect it has debris restricting a passage? Its in a Tucker Sno Cat, if you know what they are? Rubber tired loaders...
  7. R

    Case 850 Long track

    It is an E. The front u-joint came apart and the driveshaft fell out. No progrossive damage. 2 u-joints, 8 bolts and 4 straps will fix it. Thanks for listening
  8. R

    Case 850 Long track

    I will know more on Sunday. Thanks
  9. R

    Case 850 Long track

    I received a call to go look at this tractor. Claims it stopped moving, no forward or reverse. Did it suddenly, like a linkage fell off, but it is still connected to the transmission and moving. I suspect something came apart inside, is it accessable with trans still in frame? Any suggestions...
  10. R

    Bobcat T190

    The issue is concuqured, two drive motors and a charge pump later. What oilm can i use in the T190, is AW 46 hydraulic oil ok?
  11. R

    Hydrostatic system

    Is it a must to use a hydrostatic oil in a shid steer, or can I use an AW hydraulic oil?
  12. R

    Bobcat T190

    No, lost track function also. Initially the brake released and the track would function.
  13. R

    Bobcat T190

    Me again.................... Installed a new charge/hydraulic pump. Followed you direction for startup. Initially had about 300 PSI charge pressure and the boom and bucket worked normal. After it started to warm up, same thing as before, 300 PSI charge pressure until you pull a function and no...
  14. R

    Bobcat T190

    This is my first hystat so bear with me. If I understand this correctly, the charge oil to the hystat pump is filtered, so no debris should be downstream of the filter. Thus there should be no additional damage to the rest of the system. My concern is if I replace this pump and have additional...
  15. R

    Bobcat T190

  16. R

    Bobcat T190

    Crewchief, I do believe you are correct. Both pump sections show where they have failed. When I first disassembled the pump I looked at the brass plates and they were not chewed to bad. When I was washing, I found the damage to the inlet side of both the charge pump and the hydraulic pump...
  17. R

    Bobcat T190

    Hey Crewchief; I just read your note again, and it said gear pumps. What is the failure in a gear pump? My experience with gear pumps is they are durable?
  18. R

    Bobcat T190

    So does crapped out mean pumps and motors or just the pump? If the pump failed and sent debris to the motors, they are most likely junk also, correct?
  19. R

    Bobcat T190

    Ok, checked belt and its tight and the pump continues to rotate. I them disconnected the steel pilot pressure line from the outlet of the filter that feeds the valve bank. I attached a gauge to that port, so now the lift section and valve bank are disconnected, 310 PSI until I pull a track...
  20. R

    Bobcat T190

    I will check that tomorrow and let you know. Thanks
Top