• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Search results

  1. P

    Bobcat Rubber Grip Replacement

    Google "Metri-pack terminals". They do make a tool to remove, but can be done with "modified" paper clip.
  2. P

    1979 Bobcat 632 can't keep it running

    If it's a ford I would make sure you have power to the positive side of the coil when the key is in the on position. When the machine cranks the R terminal on the start supplies 12v to the coil positive terminal. When you let the key go- to the run position- the voltage to the pos. coil stud is...
  3. P

    Bobcat T190 instrument panel

    dodgedad, try holding the run/enter button for 10 seconds. This should reset your deluxe panel settings.
  4. P

    Drive Motor - Grinding/Squeling Noise?

    Sound like you may have a problem with brake- causing your squealing. It is possible you have a bad seal on the brake piston on the right side. The left and right side brakes are released by a common supply, so if the seal on the right is not holding and dumping in the motor, the pressure to the...
  5. P

    843 drive problem

    Check the filter- under the fitting- at the #9 location for blockage. This will cause an issue with charge pressure to the pumps. Pull it out an try to blow thru it. You can also remove it completely and reinstall the fitting- for testing purposes.
  6. P

    743 temperature sending unit

    One wire sender is on thermostat housing.
  7. P

    Error Code 21-02 BobCat 425 Mini Excavator

    Glow plug relay
  8. P

    A300 Service Peep

    Press the light button to turn on panel and then press and hold HIGH FLOW and AUXILLARY PRESSURE RELEASE buttons at the same time. RESET will appear in hour meter display. This will just reset it - not shut it off for good
  9. P

    873 Valve clearance spec

    .012 intake .020 exhaust
  10. P

    Bobcat 763. No auxiliary hydraulics and no bucket leveling.

    Both front aux and bucket positioning would be items which would need to be turned on when replacing a controller in your machine. If the problem is in fact that they are not turn, on your dealer should be able to tell you in a short amount of time by hooking up their laptop and seeing if those...
  11. P

    Bobcat diagnostic tool and software S185, S300,T190 and so on

    On the older panels, press the light button to turn on panel and then press and hold HIGH FLOW and AUXILLARY PRESSURE RELEASE buttons at the same time. RESET will appear in hour meter display. This will just reset it - not shut it off for good
  12. P

    Bobcat 863

    That style connection is retained internally with a spring clip, inside the cooler. The tool to remove it looks similiar to an OTC6594. If it is not staying in it may either be the spring clip or the fitting on the hoss. The tool more or less puts pressure on the clip to spead it and release the...
  13. P

    S185 loader arms settling fast

    The valve next to the seat is a lift bypass. If it is leaking internally it could cause this problem. With the arms down you can remove and cap the inlet to the bypass valve- it is the line coming from the control valve- the outlet line is going to the tank. Once line and fitting are capped lift...
  14. P

    Fuel lift pump replacement

    You can unbolt and install that pump with no worries.
  15. P

    743b fuel selenoid wiring

    Don't know if this answers question, at the engine harness 3 wire plug you should have 1 ground and 2 switched power wires. When you plug in the timer, at the solenoid side, you will have 1 ground, 1 switched power (hold), and 1 timed power (pull).
  16. P

    bobcat t300 how to overide defeat safety bar switch?

    Well said ATCO.
  17. P

    863 bobcat hyd problem

    First off need to eliminate the electrical system- switch, controller, solenoids, ect. Its very easy to do as ATCO said. An easy thing you can do if nothing seems to work is to turn key on- don't start, turn on aux, raise cab, loosen aux stem nuts, and run aux rocker switch. If electrical is...
  18. P

    Need Hyd help on my 863G

    Aux should be either opening or closing the grapple when you start it with attachment on. Swap the stems/coils and see if grapple goes in opposite direction.
  19. P

    Oil cooled Duetz/Gehl 4835

    Should be stamped "IN" and "OUT" on block. OUT should be plumbed to the heater control valve, then to heater core and then back to IN port
  20. P

    Need Hyd help on my 863G

    Aux are definately engaged. Could be sticking spool or sticking stem. Do you have any attachments- auger or broom would do. Hook attach to machine and note which direction it spins. Then remove and swap aux stems- front to back- and restart. If attachment rotates in opposite direction you have a...
Top