• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Recent content by wsw

  1. W

    John Deere 770A - Recently Purchased - Gear Change Query

    It has been yrs since I done a trans in an A model but you have lost a clutch, you can pressure tap most clutches externally
  2. W

    Deere 270 stuck arm

    I have a Deere 270LC the arm locks up, when I go to bring the arm in the main hydraulic valve is not letting the oil from the other side of the cylinder return to the tank, If I go and back off the relief valve from arm out side then the arm will come in, If I want to move the arm out then I...
  3. W

    hitachi exe200 lc-s hydraulic problem stallin out engine

    Main pressure is going down because your pilot pressure is now sufficient to open valve spools. It sounds like it is spooling up the pumps before it moves the valve spools, are you sure the pumps are not spooling up?
  4. W

    Case 821B final drive parts

    I assumed you have filled it with fuel, on the side of the transfer pump there should be an arm for priming. If you have run it completely out then it is easyest if you crack open some fuel injection lines at the Injector and pum up the primer with key in on possition until you get fuel out of...
  5. W

    Case 821B final drive parts

    Send me a private message
  6. W

    Caseih 5130 PTO problems

    Thanks alot for your help guys Take Care
  7. W

    Caseih 5130 PTO problems

    But I access this from the rear of the tractor? I will have no problem doing this I am just not familiar with this machine, I just finnished a complete transmission rebuild on a Cat 966G loader. I work mostly on heavy equipment and also on Cat diesels in trucks and yachts. Thanks for...
  8. W

    Caseih 5130 PTO problems

    Is this something you access through the rear of tractor or from top, below the seat? Is it usually hydraulic or mechanical ? thanks Iron@Dirt
  9. W

    Kobelco hydraulic excavators

    To Wheelz I would throw an " out of service tag " on the exterior of the door and one in the cab covering the key switch and they cannot fine you then
  10. W

    Caseih 5130 PTO problems

    I have not been there yet but they say this tractor you spin the shaft around for 1000 from 540 PTO speed
  11. W

    Truck Shakes when loaded

    I would look at driveline angles then or the slip yoke could be bottoming, ujoints should neer be more than 15 degrees and that is alot I would like to say 11 or 12 degrees, Also retorque the rear u bolts while the truck is loaded. not appling enough torque while the spring is unsprung will...
  12. W

    Truck Shakes when loaded

    You say it shakes but you never said if it was in the steering wheel or seemed to be coming from the drivetrain. And is it a shake or a shimmy? How much does the rear of the truck drop as it is loaded. Answer these questions so I can better help you
  13. W

    Case 821B final drive parts

    Looking for final drive/axle parts for a 1995 Case 821B wheel loader. I haven'y seen machine yet but I will tomorrow
  14. W

    Caseih 5130 PTO problems

    I have a customer with a Case ih 5130 Maxum and they told me the PTO just suddenly stopped, I am mostly heavy equipment repair but this is a good customer and I will be going out to look at it as soon as I am done with the current job. Any advise ?
  15. W

    ford 3000 help

    Did it sit for a while with now fuel in it? I will tell you if you have one injector stuck open the cylinder following it in sequence will also be underfueled if it has a rotary pump
See more
Top