• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Tony Wells's latest activity

  • Tony Wells
    Tony Wells replied to the thread Doosan 250-3 Regen.
    minor update Put a new stat in. Shop mgr ordered original -3 stat, which is 165° F. Runs at 167°, will not get warm enough yet. Robbed...
  • Tony Wells
    Tony Wells replied to the thread Doosan 250-3 Regen.
    minor update Put a new stat in. Shop mgr ordered original -3 stat, which is 165° F. Runs at 167°, will not get warm enough yet. Robbed...
  • Tony Wells
    Tony Wells replied to the thread Doosan 250-3 Regen.
    Great tip! I'll check that early on. My accomplice on this one, since I'm in no shape to be climbing all over these machines due to some...
  • Tony Wells
    Tony Wells reacted to old timer's post in the thread Doosan 250-3 Regen with Like Like.
    Hi Tony. The pilot disable (hydraulic lock) switch is in the right side switch panel, should be the first one of the inside line of...
  • Tony Wells
    Tony Wells reacted to old timer's post in the thread Doosan 250-3 Regen with Like Like.
    Hi Tony, There is a lot to unpack there. First, solve the water in fuel sensor problem. Second, install a new thermostat (advise to get...
  • Tony Wells
    Tony Wells reacted to old timer's post in the thread Doosan 250-3 Regen with Like Like.
    Hi Tony, Did a dive into your codes, the 2 I would worry about is a 'EGR timeout' (likely a loose or corroded connector) and a...
  • Tony Wells
    Tony Wells replied to the thread Doosan 250-3 Regen.
    LOL...I carry both fuel and extinguisher, depending on what catches fire. Some I'd rather see in ashes OK, then first I'll see about...
  • Tony Wells
    Tony Wells replied to the thread Doosan 250-3 Regen.
    old timer, I agree...there's a lot going on with this machine. One step at a time will get there though. I'll tackle the water in fuel...
  • Tony Wells
    Tony Wells replied to the thread Doosan 250-3 Regen.
    OK....today I spent a little time with the machine. First problem was that I could not get it warm enough. After 15 minutes at idle...
    • IMG_6559.jpg
    • IMG_6561.jpg
    • IMG_6562.jpg
  • Tony Wells
    Tony Wells reacted to old timer's post in the thread Doosan 250-3 Regen with Like Like.
    If that is a Doosan DL250-3, make sure the machine is at least at 170F, the park brake enabled, hydraulics disabled, and the machine is...
  • Tony Wells
    Tony Wells replied to the thread Doosan 250-3 Regen.
    Thanks again! I'll have a go at it in the morning. I'll post any codes I find, and go from there. I was not aware of the park brake...
  • Tony Wells
    Tony Wells replied to the thread Doosan 250-3 Regen.
    Thanks, Old Timer, for the reply. I've read instructions similar to yours. I believe I've followed them. The only fuzzy area is exactly...
  • Tony Wells
    Tony Wells posted the thread Doosan 250-3 Regen in Wheel Loaders.
    Gentlemen, I am seeking additional information on a particular (and peculiar it seems) RTL. It's a DL250-3. From what I understand, if...
  • Tony Wells
    Tony Wells posted the thread Doosan forced regen... in Tractor/Loader/Backhoes.
    Gentlemen, I am seeking additional information on a particular (and peculiar it seems) RTL. It's a DL250-3. From what I understand, if...
  • Tony Wells
    Tony Wells reacted to Welder Dave's post in the thread Straightening a hydraulic cylinder rod (JCB 212s, backhoe bucket cylinder) with Like Like.
    Best to use aluminum V blocks or pieces of aluminum/brass in the V blocks and under the hyd. ram. Generally you want to push the rod a...
Show older items
Top