• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Recent content by ozarkag

  1. O

    CAT 277d DPF code

    How bought lying to the ecm and saying the dpf has been cleaned. Soot load reset in the software. If it actually needs cleaning will regen on differential pressure.
  2. O

    3 wire alternator nightmare

    Not sure why the jumper to terminal 2. Should work without that. But definitely agree, go with the 1 wire. It will either work or not. . .
  3. O

    Cat 299D - 723-8 Error Code - Engine position Sensor - Abnormal Frequency - Pulse Width or Period

    For these sensor plugs try ballengermotorsports.com Probably have to match up by number of terminals (2) brand, (denso) and images.
  4. O

    Cat 299D - 723-8 Error Code - Engine position Sensor - Abnormal Frequency - Pulse Width or Period

    Unplug that sensor, should start just fine on one sensor. Will crank a bit longer before it fires. Then also try it vice versa
  5. O

    Deere ECM Repair Shop?

    I sent one to a shop in S C . Pure scam, never was opened.
  6. O

    TL 10 fan air flow direction

    I believe it will blow out thru the back. could be wrong
  7. O

    CAT 277d DPF code

    We've had some luck removing and physically cleaning the dpf after an event such as turbo failure. Using hot water pressure washer with the tip removed. So basically just rinsing, no pressure. With no codes except regen frequency it may very well work to reset several times and try to run it...
  8. O

    Bobcat T595 setting water in fuel code

    It is not likely the filter is the issue, the sensor is simply 2 prongs into the fuel. Nothing proprietary at all. I would not use the aftermarket filters tho, I've cut one open. . . And these injectors are very susceptible to contamination. We did build a filter base kit to use Donaldson...
  9. O

    Cat overcharging

    Alternator
  10. O

    Identifying head gasket kubota v3300-eb2

    Difference is gasket thickness, correct gasket is determined by measuring piston protrusion. Not sure on why some times they use a graphite gasket, and seems when they do there are no thickness choices. 1 and 2 notch are the middle choices and seem to be the most common.
  11. O

    Case 75 XT SKID STEER INTERLOCK

    Rops interlock is left rear cab corner, contacts frame when cab is down. Is wired in series with lap bar, I often bypass it at harness by lap bar sensor.
  12. O

    bobcat t320

    What is the code? Starts runs and drives? First step is to verify power and ground to affected controller, also check for any obvious wire damage.
  13. O

    Replacing halogen with leds

    Unfortunately lumen ratings are not an exact science. Even big name brands have issues with over rated lumen output. 2700 is believable, 6000 rated ones may or may not be brighter in real life.
  14. O

    JCB 205 skid steer filters

    Maybe build a relationship with a local dealer? Some/most of the filters and most parts will be OE only. Otherwise work up a cross list of filter numbers and search those.
  15. O

    2014 T7 70 2600 charged pressure low after warm-up

    Verify pressure with an actual Guage, could be a sensor issue. Course that would be too easy.. . . Pull the charge relief valve (back center of pump) maybe just change it. I've seen some with a stack of shims where somebody was struggling with it. Check case drain flows from both drive...
See more
Top