• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Recent content by Jonmiller

  1. J

    Hitachi MPDR Issue

    We have imported a Few Hitachi ZX130's-5 and 6's and we have realized that we are not able to connect to them with the US Version of MPDR that we are from provided from John Deere. Wondering If there is some one from across the Pond that may be able to help us get the correct MPDR to work on...
  2. J

    Komatsu -10 passcode Disable

    Thank you guys for the help the procedure worked.
  3. J

    Komatsu -10 passcode Disable

    I have a Komatsu Pc138-10 that we bought at a auction how do we disable the Start Passcode in the machine? is there a Hidden menu i dont know about that would help disable it?
  4. J

    Sakai T2 Manual

    Looking for a Sakai T2 or TS200 shop manual have some wiring issues I'm trying to resolve. thanks for the help Serial number is 21807
  5. J

    Dump Body on Moxy MT 30 does not want to come down

    Been a while and might not even be the same vintage of truck but i had one that had a box proximity switch in the back by the pivoting pins that went bad and did the same thing guy raised the box up and couldn't get it back down. Might be worth looking into you should be able to see them with...
  6. J

    Case 340 Code MUX 118

    Just a Heads up i didn't even know Case branded a off road truck till this came in. What i have is a Case (Astra) 340 Off road truck SN, HHD000704. I have a code flashing on the Dash that is a "MUX 118" I have some what of a service manual in rough shape and it says something about. Notes: "The...
  7. J

    980H rough Idle

    Being that we are not A cat dealer do we need a Cat tech to come and flash this ECM??
  8. J

    980H rough Idle

    So maybe dumb question what is the FLT and FLH as im not very good with cats (mainly work on Komatsu Deeres and JCB's)
  9. J

    980H rough Idle

    Yes as if the Key had been shutoff the only change on the dash is the warning light comes on and the coolant gauge sweeps. And it does say "Engine Over speed Shut Down" and "Cold mode" flashes. And what would you like screen shot or photos of?
  10. J

    980H rough Idle

    I have a Code 268-2 For engine parameters but i never did anything with that stuff
  11. J

    980H rough Idle

    I have a 980H that ran great when we pulled the machine into the shop. We pulled the cab and replaced some hoses reinstalled the cab. Now we are experiencing every 10 seconds while idling the machine shuts off and turns then back on. We hooked up a laptop to the machine and at that the time it...
  12. J

    Kobelco SK170-9 Pilot control Issue??

    I have a Kobelco SK170-9 we went to start it today after sitting for a couple months. I have no Pilot controls i did some quick google searching and found what they said to be the Pilot control solenoid to be on Port A1. I checked power there and when i put the lock lever down i get 24v's but...
  13. J

    Cat It28G intermitten shift

    I have gotten some new data i pinned out the ecm when it was working and inop i emailed you nigel and was wondering what you get of the data thanks for your help
  14. J

    Cat It28G intermitten shift

    I didnt get the email with the Schematic
  15. J

    Cat It28G intermitten shift

    Ok i back probed the controller and got my voltage readings and from pin 23-27 read 0 volts pin 28-29 read 1.4 volts each and pins 30-40 had 0 volts and also i tryed to match these numbers and colors to the two schematics i do have and they dont match either why would this be ?
See more
Top